Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

CCM end call

Hi i have next sheme CCM6.1 -> 2821 with vic2/4fxo and em-hda-6fxo-> PBX -> pstn.

All incoming call goto over vic2/4fxo on ip phone. Then secretary transfer call on pbx over em-hda-6 fxo and subscriber end call to hang up the receiver. Port on vic2/4fxo and em-hda-6fxo not remain in status UP. How i can fix it?

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 0/1/1

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 0/1/2

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 0/1/3

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/0

!

voice-port 2/0/1

!

voice-port 2/0/2

!

voice-port 2/0/3

!

voice-port 2/0/4

!

voice-port 2/0/5

!

voice-port 2/0/6

!

voice-port 2/0/7

!

voice-port 2/0/8

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/9

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/10

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/11

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/12

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

voice-port 2/0/13

cptone RU

timeouts call-disconnect 1

timeouts ringing 5

timeouts wait-release 1

timing hookflash-out 500

connection plar opx 460

caller-id enable

!

!

!

dial-peer voice 2000 voip

destination-pattern ...

session target ipv4:10.10.18.5

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 2001 voip

incoming called-number .

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 101 pots

preference 8

destination-pattern 9T

port 0/1/0

!

dial-peer voice 102 pots

preference 9

destination-pattern 9T

port 0/1/1

!

dial-peer voice 103 pots

preference 10

destination-pattern 9T

port 0/1/2

!

dial-peer voice 104 pots

preference 7

destination-pattern 9T

port 0/1/3

!

dial-peer voice 2002 voip

shutdown

destination-pattern 66401

session target ipv4:10.10.18.5

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 208 pots

preference 1

destination-pattern 9T

port 2/0/8

!

dial-peer voice 209 pots

preference 2

destination-pattern 9T

port 2/0/9

!

dial-peer voice 210 pots

preference 3

destination-pattern 9T

port 2/0/10

!

dial-peer voice 211 pots

preference 4

destination-pattern 9T

port 2/0/11

!

dial-peer voice 212 pots

preference 5

destination-pattern 9T

port 2/0/12

!

dial-peer voice 213 pots

preference 6

destination-pattern 9T

port 2/0/13

1 REPLY
Bronze

Re: CCM end call

It may be necessary to shut/no shut the voice port to have the changes take effect.

If not, then it would seem that any caller-id information received from the VG224 phone overrides the station-id configs. Can you configure the VG224 phone to not send any caller-id information.

In the planned topology, the FXO port was connected to the Intercom system. Would the intercom system be sending caller-id information like the VG224 phone is doing? If not, then the station-id info would be sent.

208
Views
0
Helpful
1
Replies
CreatePlease to create content