Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CCM5 integration with MGCP 3845 GW

We have a problem in regestering our CCM 5.0 and the 3845 voice GW router, the CCM shows the router as unregestered with the IP Address, and the router I noticed that I'm not able to show the MGCP endpoints. please how can I verify or point to the problem.

3 REPLIES
Cisco Employee

Re: CCM5 integration with MGCP 3845 GW

verify your config, maybe you're missing the service mgcp under the pri-group.

maybe the dial-peers do not have the application mgcpapp commmand.

maybe you selected the wrong slot.

if possible post your config

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: CCM5 integration with MGCP 3845 GW

thanks, we are using BRI interfaces, below is the router configuration:

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

supplementary-service h450.12

h323

!

!

!

voice class codec 1

codec preference 1 g729r8

!

!

!

!

!

!

!

!

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server 10.65.60.4

ccm-manager config

!

!

username admin password 0 ad-tech123

!

!

!

!

interface GigabitEthernet0/0

ip address 10.65.60.5 255.255.255.0

duplex auto

speed auto

media-type rj45

!

interface Service-Engine0/0

ip unnumbered GigabitEthernet0/0

service-module ip address 10.65.60.6 255.255.255.0

service-module ip default-gateway 10.65.60.1

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

media-type rj45

!

interface Serial0/0/0

no ip address

shutdown

clockrate 2000000

!

interface Serial0/0/1

no ip address

shutdown

!

interface BRI0/1/0

no ip address

isdn switch-type basic-net3

isdn point-to-point-setup

isdn incoming-voice voice

!

interface BRI0/1/1

no ip address

isdn switch-type basic-net3

isdn point-to-point-setup

isdn incoming-voice voice

!

ip classless

ip route 0.0.0.0 0.0.0.0 10.65.60.1

ip route 10.65.60.6 255.255.255.255 Service-Engine0/0

!

!

ip http server

no ip http secure-server

!

!

!

!

control-plane

!

!

voice-port 0/1/0

compand-type a-law

cptone JO

timeouts interdigit 3

connection plar 199

!

voice-port 0/1/1

compand-type a-law

cptone JO

timeouts interdigit 3

connection plar 199

!

mgcp

mgcp call-agent GetCCM 2427 service-type mgcp version 0.1

mgcp rtp unreachable timeout 1000 action notify

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

!

!

dial-peer voice 3 voip

destination-pattern [1-4]..

session protocol sipv2

session target ipv4:10.65.60.6

dtmf-relay sip-notify

codec g711ulaw

no vad

!

dial-peer voice 1 pots

application mgcpapp

port 0/1/0

!

dial-peer voice 2 pots

application mgcpapp

port 0/1/1

!

dial-peer voice 100 pots

preference 1

destination-pattern 9T

port 0/1/0

!

dial-peer voice 101 pots

preference 2

destination-pattern 9T

port 0/1/1

!

end.

New Member

Re: CCM5 integration with MGCP 3845 GW

and here below some result for debug mgcp:

*Apr 28 07:28:34.903: mgcpapp_process_mgcp_msg : socket drained.

*Apr 28 07:28:34.903: MGCP sys msg: (15)

*Apr 28 07:28:34.903: xlate sys msg: (15, 65532148)

*Apr 28 07:28:34.903: sys msg values: (INVALID MGCP EVENT, 65280, , 1619485180, CALL_IDLE)

*Apr 28 07:28:34.903: process mgcp_handle_cmapp_event

*Apr 28 07:28:34.903: mgcp_cmapp_send_keepalive send NTFY KeepAlive

*Apr 28 07:28:34.903: xgcp_endpt_get_by_ifn

*Apr 28 07:28:34.903: xgcp_endpt_get_tree_link_by_ifn

*Apr 28 07:28:34.903: xgcp_endpt_compute_key- type -1 slot -1 subunit 58

*Apr 28 07:28:34.903: xgcp_endpt_get_tree_link_by_ifn : computed key 0x0xF0000000

*Apr 28 07:28:34.903: send_mgcp_empty_notify_msg: endpt *, complete_endpt *@getmgcp.getecom.com

*Apr 28 07:28:34.903: -- mgcp_build_packet()-

*Apr 28 07:28:34.903: - mgcp_estimate_msg_buf_length() - 328 bytes needed for header

- mgcp_estimate_msg_buf_length() - 373 bytes needed after checking parameter lines

- mgcp_estimate_msg_buf_length() - 373 bytes needed after cheking SDP lines

*Apr 28 07:28:34.903: --- mgcp_build_parameter_lines() ---

- mgcp_val_mandatory_parms()

- mgcp_build_request_id()

- SUCCESS: Request ID string building is OK

- mgcp_build_obs_events()

- mgcp_build_obs_events()- mp_head_obs_evt_list NOT NULL

- mgcp_build_obs_events()- out of for loop for next node in list

- SUCCESS: Building MGCP Parameter lines is OK

*Apr 28 07:28:34.903: - SUCCESS: MGCP message building OK

*Apr 28 07:28:34.903: - SUCCESS: END of building

*Apr 28 07:28:34.903: * mgcp_get_ca_addr_port:

*Apr 28 07:28:34.903: * mgcp_get_ca_addr_port: Used endpoint NE 10.65.60.4:2427

*Apr 28 07:28:34.903: * mgcp_get_ca_addr_port: NE addr 10.65.60.4:2427

*Apr 28 07:28:34.903: * mgcp_enq_retx_msg: trans_id 59,ntfy_ent 10.65.60.4:2427

*Apr 28 07:28:34.903: * mgcp_root_get_profile:

*Apr 28 07:28:34.903: mgcp_add_trans_id_rec: Add trans id (59, 648ECC30) record

*Apr 28 07:28:34.903: mgcp_stw_timer_start timer type 0, duration 500

*Apr 28 07:28:34.903: MGCP Packet sent to 10.65.60.4:2427--->

NTFY 59 *@getmgcp.getecom.com MGCP 0.1

X: 0

O:

<---

*Apr 28 07:28:34.903: send_mgcp_empty_notify_msg NTFY Packet sent successfully - *

*Apr 28 07:28:34.903: MGC stat - 10.65.60.4, total=67, succ=42, failed=24

*Apr 28 07:28:34.903: MGCP Packet received from 10.65.60.4:2427--->

200 59

<---

*Apr 28 07:28:34.903: mgcpapp_process_mgcp_msg : processing received message.

*Apr 28 07:28:34.903: -- mgcp_parse_packet() - call mgcp_parse_header

*Apr 28 07:28:34.903: mgcp_parse_response : 200 59

*Apr 28 07:28:34.903: mgcp_string_parse: return code=1.- mgcp_parse_packet() - out mgcp_parse_header

- SUCCESS: mgcp_parse_packet()- MGCP Header parsing was OK

- SUCCESS: mgcp_parse_packet()- END of Parsing

*Apr 28 07:28:34.903: * mgcp_msg_ack

*Apr 28 07:28:34.903: MGC stat - 10.65.60.4, total=67, succ=43, failed=24

*Apr 28 07:28:34.903: * mgcp_msg_ack: Removing msg : NTFY 59 *@getmgcp.getecom.com MGCP 0.1

X: 0

O:

*Apr 28 07:28:34.903: * mgcp_msg_ack: Setting the restart method to NONE

*Apr 28 07:28:34.903: mgcpapp_process_socket

*Apr 28 07:28:34.903: mgcpapp_process_mgcp_msg : socket drained.

233
Views
0
Helpful
3
Replies