Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CFwdALL error database

We're getting "error database" whenever anyone tries to Cfwdall their line. I've gone through knowledge base solution K20424904, but none of the suggestions worked. Previously we reset our "Private Password phrase", but checking this it looks like everytning is in sync. The only event entry that may apply to this is an Application Informational message MSSQLSERVER - Login failed for user '[null'. Reason: Not associated with a trusted SQL server connection.

Not sure how to proceed.

9 REPLIES
Hall of Fame Super Red

Re: CFwdALL error database

Hi Frank,

Hope all is well with you! Sounds like a Replication issue :( If the Pub is down or Replication between the Pub and Subs is broken no changes can be made to CFWD ALL. Here is a doc that speaks to this question;

This is a list of possible symptoms if the subscriber stops replicating from the publisher:

Changes that are made on the publisher are not reflected on phones that are registered with the subscriber.

Outbound calls fail on phones registered with the subscriber. As soon as you dial 9 you hear a re-order tone.

Call Forward All (CFwdALL) does not work.

IP phone displays Error Database.

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801e7ddf.shtml

And this good doc;

Cisco CallManager Issues with Call Forward All

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801b3f4b.shtml

Hope this helps!

Rob

New Member

Re: CFwdALL error database

Hi Rob,

I don't think replication is my problem. I followed the note09186a00801b3f4b instructions for both dblhelper and created a dummy record and verified it existed on the subscriber. I also verified Telephone call dispatcher is active on both publisher and subscriber. Right now I'm at loss.

VIP Super Bronze

Re: CFwdALL error database

Kirstein,

I have seen a case where changes made were seen on the sub as you have done with the dunny record and yet I still have replication problems...

I suggest to you to run dblhelper....and check the status of your replication...do not assume anything..check evrything...CFWALL is a sign of replication problem...certainly.

Also make sure you run dblhelper from the the bin directory.

You should also use the admin utility to check password sync across your cluster...

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: CFwdALL error database

First, I'd like to thank everyone for their responses. In the end, on Cisco's advice, I rebooted the subscriber and it worked. It's likely setting the password phrase, although it's not specified to do so, requires a subscriber reboot.

Thank you again.

Green

Re: CFwdALL error database

It doesnt

when you run adminutility it stop starts all Cisco Services and SQL services which are using our accounts

Green

Re: CFwdALL error database

Replication at CCM level was you problem since CCM has internal tables in cache which interacts with SQL via DBL DLLs.

Bronze

Re: CFwdALL error database

If call forwarding was working before and it stop working, you might have a SQL database replication issue between Publisher and Subscriber.

Please stop and start the DBL service on the Publisher and then subsequently on the Subscriber(s).Restart the DBL service on the Publisher and then on the subscriber(s). If that does not resolve theissue please stop and start the CTI Manager service in the same way. If things are still not working then please try to ping from the subscriber the phones are registered to to the Publisher's hostname. Is the name resolved right away ? Do you have a DNS server setup ? If so, please remove the DNS server config and configure your LMHOSTS file.

New Member

Re: CFwdALL error database

This is probably a stupid question, but how do you stop and start the DBL? CTI have been stopped and started with no help.

Re: CFwdALL error database

On the server go to Start --> Run and type services.msc a page will open with all the services and just stop and start the Database Layer Monitor service

177
Views
3
Helpful
9
Replies
CreatePlease to create content