Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CIPC / CCME Question

Hi,

Does anyone specifically know whether there is a firmware parameter required for CIPC ("load" command) when running it with CCME?

I have doen a fair bit of digging and all I can see so far is that you can specify the phone type as "type cipc".

I understand that CIPC is basicaly an emulation of 7970, so isn't the 7970 load appropriate?

Thanks,

Chris

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: CIPC / CCME Question

Hi Chris,

I have not setup CIPC with CME but according to the attached doc no firmware is required. Have a look;

Cisco IP Communicator 2.0

**No firmware required**

Cisco IP Communicator 2.0 is supported by Cisco CallManager Express 3.3 using Cisco IOS Software Release 12.4.

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a00805f6cb4.html

Cisco IP Communicator Overview (CME)

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_guide_chapter09186a00806a7ffb.html#wp1010500

Use the normal phone provisioning commands. In the "type" command, use the "CIPC" keyword to identify this phone as a Cisco IP Communicator.

Hope this helps!

Rob

9 REPLIES
Hall of Fame Super Red

Re: CIPC / CCME Question

Hi Chris,

I have not setup CIPC with CME but according to the attached doc no firmware is required. Have a look;

Cisco IP Communicator 2.0

**No firmware required**

Cisco IP Communicator 2.0 is supported by Cisco CallManager Express 3.3 using Cisco IOS Software Release 12.4.

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a00805f6cb4.html

Cisco IP Communicator Overview (CME)

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_guide_chapter09186a00806a7ffb.html#wp1010500

Use the normal phone provisioning commands. In the "type" command, use the "CIPC" keyword to identify this phone as a Cisco IP Communicator.

Hope this helps!

Rob

New Member

Re: CIPC / CCME Question

Rob,

That is a helpful response. Although I had read the second document already this did nothing to confirm whether there was any requirement or not, however the first link is clear enough...

Thanks again,

/Chris

New Member

Re: CIPC / CCME Question

Chris,

I could not get my CIPC working with my CCME4.0.

If you have a solution by now, please help.

Joe

Re: CIPC / CCME Question

Joe,

Make sure you put "type CIPC" under the ephone that you created for the IP Communicator.

New Member

Re: CIPC / CCME Question

Shanky,

I have the command in, but it still does not work.

Joel

Re: CIPC / CCME Question

Please paste your relevant CME configs.

New Member

Re: CIPC / CCME Question

Shanky,

This is my config.

tftp-server flash:P0030702T023.bin

tftp-server flash:P0030702T023.loads

tftp-server flash:P0030702T023.sb2

tftp-server flash:P0030702T023.sbn

tftp-server flash:TERM41.7-0-3-0S.loads

tftp-server flash:TERM70.7-0-3-0S.loads

tftp-server flash:S00105000200.sbn

telephony-service

video

maximum bit-rate 128

no auto-reg-ephone

load 7960-7940 P0030702T023

load 7914 S00105000200

load 7941GE TERM41.7-0-3-0S

load 7961GE TERM41.7-0-3-0S

load 7971 TERM70.7-0-3-0S

max-ephones 52

max-dn 104

ip source-address 192.168.82.1 port 2000

max-redirect 20

no caller-id name-only

service phone videoCapability 1

system message Eng Engineering, Inc.

url services http://phone-xml.berbee.com/menu.xml

time-zone 12

time-format 24

voicemail 2050

mwi relay

max-conferences 16 gain -6

call-park system redirect

moh flash:music-on-hold.au

web admin system name xxxx secret 5 xxxxx

dn-webedit

time-webedit

transfer-system full-consult

transfer-pattern 9.T

secondary-dialtone 9

ephone 41

device-security-mode none

video

mac-address 0005.9A3C.7800

type CIPC

button 1:39

Joe

Hall of Fame Super Gold

Re: CIPC / CCME Question

Definitely there are no load commands to give, the CIPC is self-contained excpet that if you configure locales on the CCME that will just mess the font on the display.

What is that is not working ?

Is the phone to registering, unable ot place calls, or what ?

New Member

Re: CIPC / CCME Question

Guys,

I was using the CIPC through the VPN client. When I upgraded the CIPC from 2.0.1.1 to 2.0.2.0 and the VPN client from 4.8.02.9 to 4.8.02.10 it started working.

Joe

2667
Views
0
Helpful
9
Replies