Cisco 1861E IOS 15.1(3)T CME 8.5

[dcolarte]

Hello,

I am trying to enable the CME GUI on an 1861E but am having great difficulty.  I uploaded what I thought were the necessary files into flash but when I attempt to access the GUI I get a page that is missing items.

If someone could spell out the process more clearly that Cisco documentation on how to enable the GUI & which files need to be loaded into flash, it would be greatly appreciated.

Thanks in advance.

DC

[ronpatel]

Hi,

Attach Configuration of CME please. Also let us know what broswer you are using.

Regards

Ronak Patel

[dcolarte]

Hi Ronak,

Sorry for the late response. I did not receive a notice that anyone responded.  In any case, here is the Config:

Router>enable
Router#show run
Building configuration...

Current configuration : 2690 bytes
!
! Last configuration change at 22:17:14 pst Tue Mar 13 2012 by admin
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
clock timezone pst -4 0
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
dot11 syslog
ip source-route
ip cef
!
!
!
!
ip dhcp pool VOICE
   network 192.168.100.0 255.255.255.0
   option 150 ip 192.168.100.1
   default-router 192.168.100.1
!
!
no ipv6 cef
multilink bundle-name authenticated
!
!
!
!
!
!
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to sip
!
!
!
!
!
voice-card 0
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid C1861E-SRST-C-F/K9 sn FTX160785RZ
username admin privilege 15 secret 5 $1$JrE1$4a.BJGAPS8kcHVqE3mle80
!
!
!
!
!
!
!
interface FastEthernet0/0
description $ETH-WAN$
ip address dhcp client-id FastEthernet0/0
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
!
interface Integrated-Service-Engine0/0
no ip address
shutdown
!
interface FastEthernet0/1/0
!
interface FastEthernet0/1/1
!
interface FastEthernet0/1/2
!
interface FastEthernet0/1/3
!
interface FastEthernet0/1/4
!
interface FastEthernet0/1/5
!
interface FastEthernet0/1/6
!
interface FastEthernet0/1/7
switchport access vlan 10
!
interface FastEthernet0/1/8
switchport access vlan 10
!
interface Vlan1
no ip address
!
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
!
!
ip nat inside source list 1 interface FastEthernet0/0 overload
!
logging esm config
access-list 1 remark INSIDE_IF=Vlan10
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
!
!
!
control-plane
!
!
voice-port 0/0/0
!
voice-port 0/0/1
!
voice-port 0/0/2
!
voice-port 0/0/3
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/1/2
!
voice-port 0/1/3
!
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control
description Music On Hold Port
!
!
!
mgcp profile default
!
!
!
!
telephony-service
max-conferences 4 gain -6
web admin system name admin secret 5 $1$f/jG$YCw36SDn2AsSyadA9xvqI/
dn-webedit
time-webedit
transfer-system full-consult
!
!
line con 0
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
login
transport input all
!
ntp server 192.43.244.18
end

I am running IE 9

Thanks again,

DC

[paolo bevilacqua]

This is asked quite often. IE9 doesn't work with CME GUI. Use Firefox or older IE.

[dcolarte]

Hi Paolo,

Good to know....thank you.  Unfortunately though, it did not resolve the issue. I get the logon box, login & I am presented with the screenshot above & non of the hyperlinks work.

Thanks,

DC

[paolo bevilacqua]

Make sure you are using the right files.

Copy files to a directory, configure it with "ip http path".

[dcolarte]

I think that may very well be my issue. Which files would in fact be the "right files" for my version of IOS?  I copied the files within the CME 8.5.0 GUI folder to flash.  See image....

[paolo bevilacqua]

So you only have to configure it right.

You would have saved time by searching before asking.

[dcolarte]

You're losing me here, Paolo.  What you see above is what I had done prior to posting on this forum & it is NOT working.  So my question is, what am I missing?  I have followed Cisco's documentation for setup & the result is a CME GUI that does not work.  The logon box comes up, I enter the WebAdmin username & pw that I setup in CLI & all I get is a webpage that will not fully load.

So that being said, do you or anyone else have some insight to what I may be missing?

thank you,

DC

[paolo bevilacqua]

I think you have not read my post above.