Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup

Hi,

I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?

trunk group HuntGroup1

hunt-scheme round-robin both up

!

dial-peer voice 1 voip

translation-profile outgoing 7to11

destination-pattern .T

progress_ind setup enable 3

no modem passthrough

voice-class codec 1

session protocol sipv2

session target dns:XXXXXXXX

dtmf-relay rtp-nte

fax rate 14400

fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw

ip qos dscp cs5 media

no vad

!

dial-peer voice 300 pots

trunkgroup HuntGroup1

description TEST NUMBER

destination-pattern XXXXXXXXXX

!

voice-port 2/0

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 1

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/1

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 2

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/2

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 3

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/3

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 4

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/4

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 5

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/5

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 6

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/6

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 7

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/7

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 8

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/8

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 9

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/9

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 10

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/10

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 11

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/11

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 12

station-id number XXXXXXXXXX

caller-id enable

!

voice-port 2/12

trunk-group HuntGroup1

timeouts interdigit 3

description HuntGroup 1 Line 13

station-id number XXXXXXXXXX

caller-id enable

Message was edited by: Thomas Schmidt Added CCSIP Debug and Router Config.

Everyone's tags (3)
2 REPLIES

Re: Cisco 2432-24FXS Calls won't ring FXS ports when placed in H

Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks

Regards
Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"
New Member

Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntg

Config and Sip Debug have been uploaded.

Thanks

Tom

199
Views
0
Helpful
2
Replies
CreatePlease to create content