Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco 2911 Configuration- Caller ID Enable

Dear Sir,

I want to configure a caller ID feature of my Cisco Telephone.

I have Cisco 7945 and Cisco 9951 with camera.

I've already check our caller ID service in Telco and verified its active on my four lines and I do double check by putting the analog phone in each line and the number appears.

Here's my current configuration:

voice-port 0/0/1

cptone BR

connection plar opx 779

caller-id enable

caller-id alerting line-reversal

caller-id alerting dsp-pre-allocate

!

Please help. Thanks a lot

1 ACCEPTED SOLUTION

Accepted Solutions

Cisco 2911 Configuration- Caller ID Enable

Hello Michael,

Let's try with the basics:

voice-port 0/0/1

no cptone BR

connection plar opx 779

caller-id enable

no caller-id alerting line-reversal

no caller-id alerting dsp-pre-allocate

caller-id alerting ring 4

sh

no sh

Since you have a pretty new IOS 15.1(4)M3, you may want to try above commands. If CLID work, then you can reconfigure the CP Tone.

HTH

--
Jorge Armijo

Please remember to rate helpful responses and identify helpful or correct answers.

-- Jorge Armijo Please remember to rate helpful responses and identify helpful or correct answers.
7 REPLIES

Cisco 2911 Configuration- Caller ID Enable

Hi Micheal.

Which IOS version are you running on 2911?

Regards..

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
New Member

Cisco 2911 Configuration- Caller ID Enable

Dear Sir,

Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M3, RELEASE SOFTWARE (fc1)

VIP Super Bronze

Cisco 2911 Configuration- Caller ID Enable

Michael,

You need to check when the caller Id appears when you plug the analogue phone in. Is it after the first ring, second ring etc..please refer to the thread below for resolution to a similar issue

https://supportforums.cisco.com/thread/2237008?tstart=0

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Cisco 2911 Configuration- Caller ID Enable

Dear Sir,

For analog phone its appearing the ID.

The caller ID not appearing when I connect the Cisco Phone.

Here's my current configuration:

voice-port 0/0/1

cptone BR

connection plar opx 779

caller-id enable

caller-id alerting line-reversal

caller-id alerting dsp-pre-allocate

Thank you,

VIP Super Bronze

Cisco 2911 Configuration- Caller ID Enable

Did you try the suggestions in the thread I referred to above...?

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Cisco 2911 Configuration- Caller ID Enable

Dear Sir,

What configuration i'm going to add to my existing Structure?

Thanks.

Cisco 2911 Configuration- Caller ID Enable

Hello Michael,

Let's try with the basics:

voice-port 0/0/1

no cptone BR

connection plar opx 779

caller-id enable

no caller-id alerting line-reversal

no caller-id alerting dsp-pre-allocate

caller-id alerting ring 4

sh

no sh

Since you have a pretty new IOS 15.1(4)M3, you may want to try above commands. If CLID work, then you can reconfigure the CP Tone.

HTH

--
Jorge Armijo

Please remember to rate helpful responses and identify helpful or correct answers.

-- Jorge Armijo Please remember to rate helpful responses and identify helpful or correct answers.
287
Views
0
Helpful
7
Replies
CreatePlease login to create content