Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CISCO 2911 SIP to PRI

I am trying to get a cisco 2911 with E1/T1 cards installed to take a sip call and make outbound call over the T1 or PRI board..  In the past I used the 3800 series and I required to purchase DSP resources in order to setup the T1  as follows

 

controller T1 0/0/0

framing esf

 linecode b8zs

 pri-group timeslots 1-24

 

The issue is that unless you have DSP resources it will not allow you to setup..  I recently took a router (2911) in production out but had to reset it and once I tried to setup the system gave me not enough resources available..  DO you know another way the previous person could have accomplished the same?

 

 

 

2 REPLIES
Cisco Employee

You might have more T1/E1s,

You might have more T1/E1s, FXO, FXSs, etc. or some other config (MTP, XCODER, etc) that takes up DSPs, and you not have enough for all those endpoints, you would need to shut down the ones you're not using, or free resources from media resources configured to free up enough DSP channels to configure that T1

Look at your inventory and current config to see what you have.

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

show inventory gives me this.

show inventory gives me this.

 

NAME: "CISCO2911/K9 chassis", DESCR: "CISCO2911/K9 chassis"

PID: CISCO2911/K9      , VID: V05 , SN: FTX1618A075

 

NAME: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC3-4MFT-T1/E1  , VID: V01 , SN: FOC1750880C

 

NAME: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 1", DESCR: "VWIC3-4MFT-T1/E1 - 4-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC3-4MFT-T1/E1  , VID: V01 , SN: FOC175087WP

 

NAME: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 2", DESCR: "VWIC3-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC3-2MFT-T1/E1  , VID: V01 , SN: FOC18036Y6E

 

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN: FOC161267U3

 

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 5", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN: FOC16164BSP

 

NAME: "C2911 AC Power Supply", DESCR: "C2911 AC Power Supply"

PID: PWR-2911-AC       , VID: V04 , SN: DCA1606R49K

133
Views
0
Helpful
2
Replies
CreatePlease login to create content