Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Cisco 2911 VIC2-FXO card is not comming up (No lights) even when i connect the line to it!!

Hi,

We recently purchased  a 2911 for a client and confirmed all basic telephony which is working fine but when i connected the line from the ptsn to the fxo port it didnot go up!! this was before doing any configuration on the voice port

Is this normal or do i have to do any configuration to bring up the voice port? because the extensions surely need to call out and am sure  this ptsn line is functional since am migrating it for a traditional PABX.

Any Ideas to why. please share, am working on  tight timeline here.

2 ACCEPTED SOLUTIONS

Accepted Solutions

Can you see the voice ports?

Can you see the voice ports? Did you configure "connection plar opx #"?

Regards,

Yosh

HTH Regards, Yosh
Silver

What DSP's (PVDM2) are

What DSP's (PVDM2) are currently installed in the 2911?  Remember that these are needed to support in this case a FXO card.

 

Thanks

Tony

Please rate helpful posts

Please rate helpful posts
Thanks,
Tony
11 REPLIES

Please post your config

Please post your config.

Regards,

Yosh

HTH Regards, Yosh
New Member

Right now am not at customer

Right now am not at customer site but will be posting it soon although i did intercom config only so far.

Any ideas on which type of config is mandatory or specific for the fxo ports to be in production. (like just a quick over view)?

Can you see the voice ports?

Can you see the voice ports? Did you configure "connection plar opx #"?

Regards,

Yosh

HTH Regards, Yosh
New Member

Yes, I can see the voice

Yes, I can see the voice ports, not yet configured that option.

Could it be why the voice port doesnot come up. (No lights on port)

 

Thanks

Bronze

Check to see if you have the

Check to see if you have the voice license bundle for the router.

show license

Index 3 Feature: uck9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium

Without the voice license, no voice ports can be configured on 2900 series routers.

 

Silver

What DSP's (PVDM2) are

What DSP's (PVDM2) are currently installed in the 2911?  Remember that these are needed to support in this case a FXO card.

 

Thanks

Tony

Please rate helpful posts

Please rate helpful posts
Thanks,
Tony
New Member

its PVDM3-16 :: 16 channel

its PVDM3-16 :: 16 channel high density voice and video DSP module

New Member

its PVDM3-16 :: 16 channel

its PVDM3-16 :: 16 channel high density voice and video DSP module

New Member

Hi Mark,Did you resolve this

Hi Mark,

Did you resolve this issue?

same issue with me lights not coming up and i can configure voice ports 

licenses are ok.

router 2921

 PVDM3-64 

VIC2-4FXO

Any idea how to solve this.

Thanks.

New Member

Yes FrankI did, I found out

Yes Frank

I did, I found out that they dont light but you configure connection plar, and try calling in from out.. it should work, thats how i tested it.

OR configure dial peers and try dialing out, it should work but the ports wont light.!!

 

Regards

New Member

I have setup as follows.but

I have setup as follows.

but didn't work.

I can't see any logs when i dialing from outside.

i received ringback tone even port shutdown 

and it doesn't show any console messages when i enter shut or noshut on voice port 

voice-port 0/1/0
 signal groundStart
 connection plar opx 8508

Thanks

 

515
Views
15
Helpful
11
Replies
CreatePlease to create content