Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cisco 3925 CUME ivr script doesn't play on incoming voip dial-peer

Hi guys,

I migrated from 2821 CUME on 3925 CUME, on the 2821 had E1 link and IVR script it was working fine, after that I copy same script on new box (3925) and add on incoming dial-peer which is connect on new ISP with SIP trunk.

Please for help!

Thank you in advance.

Tom

  • IP Telephony
6 REPLIES
Silver

Could you post configs and

Could you post configs and script to give us a little bit more info?

BR,

Dragan

HTH, Dragan

Do you have a transcoder? Did

Do you have a transcoder? Did you configure the appropriate dtmf-relay and codec?

Regards,

Yosh

HTH Regards, Yosh
New Member

Hi YoshI have configured DSP

Hi Yosh

I have configured DSP :

c3925-vgw#sh dspfarm all 
Dspfarm Profile Configuration

 Profile ID = 2, Service = TRANSCODING, Resource ID = 2  
 Profile Description :  
 Profile Service Mode : Non Secure 
 Profile Admin State : UP 
 Profile Operation State : ACTIVE 
 Application : SCCP   Status : ASSOCIATED 
 Resource Provider : FLEX_DSPRM   Status : UP 
 Number of Resource Configured : 1 
 Number of Resources Out of Service : 0
 Codec Configuration: num_of_codecs:6 
 Codec : g729br8, Maximum Packetization Period : 60 
 Codec : g729r8, Maximum Packetization Period : 60 
 Codec : g711ulaw, Maximum Packetization Period : 30 
 Codec : g711alaw, Maximum Packetization Period : 30 
 Codec : g729ar8, Maximum Packetization Period : 60 
 Codec : g729abr8, Maximum Packetization Period : 60
Dspfarm Profile Configuration

 Profile ID = 1, Service = CONFERENCING, Resource ID = 1  
 Profile Description :  
 Profile Service Mode : Non Secure 
 Profile Admin State : UP 
 Profile Operation State : ACTIVE 
 Application : SCCP   Status : ASSOCIATED 
 Resource Provider : FLEX_DSPRM   Status : UP 
 Number of Resource Configured : 3 
 Number of Resources Out of Service : 0
 Maximum conference participants : 8
 Codec Configuration: num_of_codecs:6 
 Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required 
 Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required 
 Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required 
 Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required 
 Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required 
 Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required


SLOT DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0    1   32.1.3   UP     N/A  FREE  xcode   2      -         -         -        
0    2   32.1.3   UP     N/A  FREE  conf    1      -         -         -        
0    2   32.1.3   UP     N/A  FREE  conf    1      -         -         -        
0    2   32.1.3   UP     N/A  FREE  conf    1      -         -         -        

Total number of DSPFARM DSP channel(s) 4

And here is the voip dial peer:

dial-peer voice 9 voip
 description SIP Trunk 
 translation-profile incoming inclid
 service ivr-script
 session protocol sipv2
 session target dns:sip.provider.com
 incoming called-number .
 dtmf-relay rtp-nte
 codec g711alaw
 no vad

Tom

New Member

from the debug I saw how

from the debug I saw how script can't catch call leg.

Tom

I was told that ivr script

I was told that ivr script can work only on pots dial-peers and not work on voip dial-peers so I installed CUC servers with ivr script in addition to CUCM servers

New Member

Hi Can you give me some

Hi 

Can you give me some advice How I can do this (some kind of example)

 

75
Views
0
Helpful
6
Replies