Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco caller name not appear

Hi

I have CUCM integrated with my Ericsson system and i have AA on Ericsson. Ater i get connected to AA , it asks for enter extension number, when i enetered ext number for Cisco IP phone number , i get the call with unknown number. below is my debug for IP phone number 39946?. I used MGCP integration get CUCM and Ercisson.

*Nov 13 12:47:17.863: ISDN Se0/0/1:15 Q931: RX <- SETUP pd = 8  callref = 0x00FB

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech 

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA18394

                Preferred, Channel 20

        Facility i = 0x9FAA068001008201008B0100A1100201010201553008820301B850860101

        Progress Ind i = 0x8183 - Origination address is non-ISDN 

        Called Party Number i = 0x81, '39946'

                Plan:ISDN, Type:Unknown

        Shift to Codeset 4

        Codeset 4 IE 0x31  i = 0x80

debug isdn q931 is              ON.

NGHA-HASA-VG#

*Nov 13 12:47:17.875: ISDN Se0/0/1:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x80FB

        Channel ID i = 0xA98381

                Exclusive, Channel 1

*Nov 13 12:47:17.875: ISDN Se0/0/1:15 Q931: TX -> ALERTING pd = 8  callref = 0x80FB

        Facility i = 0x9FAA06800100820100A10C020101060528EC2C00018400

        Progress Ind i = 0x8088 - In-band info or appropriate now available

*Nov 13 12:47:17.919: ISDN Se0/0/1:15 Q931: RX <- FACILITY pd = 8  callref = 0x00FB

        Facility i = 0x9FAA06800100820100A406020101810101

*Nov 13 12:47:26.851: ISDN Se0/0/1:15 Q931: TX -> CONNECT pd = 8  callref = 0x80FB

        Facility i = 0x9FAA06800100820100A10C020102060528EC2C00028400

        Connected Number i = 0x0081, '39946'

*Nov 13 12:47:26.983: ISDN Se0/0/1:15 Q931: RX <- FACILITY pd = 8  callref = 0x00FB

        Facility i = 0x9FAA06800100820100A406020102810101

*Nov 13 12:47:26.983: ISDN Se0/0/1:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x00FB

*Nov 13 12:47:27.659: ISDN Se0/0/1:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x80FB

        Cause i = 0x8090 - Normal call clearing

Thanks

4 REPLIES

Cisco caller name not appear

Hi,

please make sure you check the "Display IE delivery" checkbox. If it does not work, you may also try the "Send Calling Name In Facility IE" checkbox.

Also, is this Q-Sig?

G.

New Member

Re: Cisco caller name not appear

Hi Gergely

Is this under gateway ?. if yes , already done. Yes i use Qsig.Please find my conf under Controller

interface Serial0/0/1:15

no ip address

encapsulation hdlc

isdn switch-type primary-qsig

isdn timer T310 120000

isdn overlap-receiving

isdn protocol-emulate network

isdn incoming-voice voice

isdn supp-service name calling profile Network-Extension operation-value-tag local

isdn bind-l3 ccm-manager

isdn send-alerting

isdn sending-complete

no cdp enable

Thanks

Re: Cisco caller name not appear

Hi,

hmm, I don't have any other clues, really. Sorry about that.

G.

Cisco caller name not appear

Hi.

Can you please indicate the version of cucm you are running?

Thanks

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
125
Views
4
Helpful
4
Replies