Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco Dial Peer Voice VOIP

Dear Sir,

Due to mis-communications of two companies, My Cisco IP telephone Dial extension is conflicting with other newly installed Telephone extension, because its started on same 4.. number.

Example;

Riyadh Branch (4 Digits) 4119

dial-peer voice 551 voip

tone ringback alert-no-PI

destination-pattern 4...$

session protocol sipv2

session target ipv4:200.200.200.13:5068

session transport tcp

dtmf-relay rtp-nte

codec g711ulaw

fax protocol none

no vad

*Newly Added Configuration*

Jeddah Branch - (3 Digits) 411

!

dial-peer voice 302 voip

corlist incoming EMPInt

destination-pattern 4..

video codec h263+

session protocol sipv2

session target ipv4:172.16.22.2

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

What will be the possible soultion, they dont want to change the extension of both Branches/Offices.

All Calls from 4 digits will automatically forward & route to 3 digits extension.

Thanks in advance.

Michael

IT

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Cisco Dial Peer Voice VOIP

Hi Michael,

Here is one solution from my side...

Apply access code to each site which are overlapping .

Suppose for Riyadh Branch access code is 7 and for Jeddah Branch code is 6. Change dial-peer according to access code and apply translation to convert those number to normal 4 and 3 digit numbers after it matches dial-peer.

voice translation-rule 1

rule 1 /^6\(4..$\)/ /\1/

!

voice translation-rule 2

rule 1 /^7\(4...$\)/ /\1/

!

!

voice translation-profile Jeddah

translate called 1

!

voice translation-profile Riyadh

translate called 2

Riyadh Branch (4 Digits) 4119

dial-peer voice 551 voip

translation-profile outgoing Riyadh

destination-pattern 74...$

Jeddah Branch - (3 Digits) 411

!

dial-peer voice 302 voip

translation-profile outgoing Jeddah

destination-pattern 64..$

Rate all the helpful post.

Thanks

Manish

2 REPLIES

Re: Cisco Dial Peer Voice VOIP

Hi Michael,

Here is one solution from my side...

Apply access code to each site which are overlapping .

Suppose for Riyadh Branch access code is 7 and for Jeddah Branch code is 6. Change dial-peer according to access code and apply translation to convert those number to normal 4 and 3 digit numbers after it matches dial-peer.

voice translation-rule 1

rule 1 /^6\(4..$\)/ /\1/

!

voice translation-rule 2

rule 1 /^7\(4...$\)/ /\1/

!

!

voice translation-profile Jeddah

translate called 1

!

voice translation-profile Riyadh

translate called 2

Riyadh Branch (4 Digits) 4119

dial-peer voice 551 voip

translation-profile outgoing Riyadh

destination-pattern 74...$

Jeddah Branch - (3 Digits) 411

!

dial-peer voice 302 voip

translation-profile outgoing Jeddah

destination-pattern 64..$

Rate all the helpful post.

Thanks

Manish

New Member

Thank you Sir Manish for the

Thank you Sir Manish for the greatful help....

259
Views
0
Helpful
2
Replies
CreatePlease login to create content