Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

cisco IP phone 7960 test

IP phone continuously display the following message,  

1. Configuring CM 

2. Opening 10.163.235.1 

Can anyone let me know the issue please? Is that looking for Call manger software from the router? if so, why call manager software is not available in 2610 router. show telephony-service is not recognized by 2610 router to check for CME software. 

How can I verify, setup, configure CME on my 2610 router? So that I can test 7960 IP phone.

Thanks in advance.

27 REPLIES

Re: cisco IP phone 7960 test

Hi Siva,

Can you post your config?

Looks like your phone has a IP address and trying to connect to the TFTP Server.

I would like to check your config/tftp server/firmware loads.

Here are some config examples that will also assist.

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_configuration_examples_list.html

hth,plz rate below if so

Thanks,

Justin

Community Member

Re: cisco IP phone 7960 test

Justin, I do not setup any tftp server. Do I need one tftp server? May i know the purpose of TFTP server?

Re: cisco IP phone 7960 test

Hi Siva,

The TFTP server is what provides the firmwar files/server information to the phone.

Here's a example

ip http server

ip http authentication local

no ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip http path flash:

!

!

!

tftp-server flash:apps31.8-3-3-17.sbn

tftp-server flash:apps41.8-3-4-16.sbn

tftp-server flash:apps75.8-3-4-16.sbn

tftp-server flash:cnu31.8-3-3-17.sbn

tftp-server flash:cnu31.8-3-3-17.sb

tftp-server flash:cnu41.8-3-4-16.sbn

tftp-server flash:cnu75.8-3-4-16.sbn

tftp-server flash:cvm31sccp.8-3-3-17.sbn

tftp-server flash:cvm41sccp.8-3-4-16.sbn

tftp-server flash:cvm75sccp.8-3-4-16.sbn

tftp-server flash:dsp31.8-3-3-17.sbn

tftp-server flash:dsp41.8-3-4-16.sbn

tftp-server flash:dsp75.8-3-4-16.sbn

tftp-server flash:jar31sccp.8-3-3-17.sbn

tftp-server flash:jar41sccp.8-3-4-16.sbn

tftp-server flash:jar75sccp.8-3-4-16.sbn

tftp-server flash:SCCP31.8-3-4SR1S.loads

tftp-server flash:SCCP41.8-3-5S.loads

tftp-server flash:SCCP75.8-3-5S.loads

tftp-server flash:term31.default.loads

tftp-server flash:term41.default.loads

tftp-server flash:term61.default.loads

tftp-server flash:term75.default.loads

!

telephony-service

load 7914 S00105000300

load 7931 SCCP31.8-3-4SR1S

load 7961 SCCP41.8-3-5S

load 7975 SCCP75.8-3-5S

ip source-address CMEIPADDRESS port 2000

Do you have your ephone and ephone dn created?

Regards,

Justin

Re: cisco IP phone 7960 test

Hello,

CME is only supported on 2600XM series routers, and not regular 2600's. This is the problem. Check the compatibility matrixes. Here's the link for further info:

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_device_support_tables_list.html

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

Justin, How do I create ephone and ephone dn? How do verify/make cisco telephony service is supported by 2610 router? When I give router#show telephony-service ; is not recognized command.

Thank you,

Re: cisco IP phone 7960 test

Hello Siva,

Please see my above post. 2610 doesnt support CME. You need to have a 2610XM.

Hope that helped, if so please rate.

Re: cisco IP phone 7960 test

Nice catch Kenneth!

Siva, if you don't have a 2600XM you can use GNS3 to simulate the IOS and CME in a lab environment.

http://www.gns3.net

Regards,

Justin

Re: cisco IP phone 7960 test

Hi Siva,

The configuration examples above will assist you in the ephone creation and understanding the terminology associated with this.

Please review the documents as I believe this will help you greatly.

Regards,

Justin

Community Member

Re: cisco IP phone 7960 test

How do i configure ephone and ephone de?

Why do I need TFTP server? CME will come along with Router?

My IP phones are getting IP address from the router(dhcp server), still do i need to go for 26xxXM?

Re: cisco IP phone 7960 test

Hello Shiva,

In order for the router to recognize the CME software that will be installed on flash memory, you need to have a 2600XM router running the proper IOS version. Otherwise, it wont work at all.

You need to have this before the router will let you configure ephone and ephone-dn's.

The phones need a TFTP server because this is how the phones pull their firmware and configuration files when they are trying to register with the CME router. In order for the phones to know where the tftp server is, you need to configure option 150 under your dhcp pool in the router. ex:

ip dhcp pool Phones

network 192.168.1.0 255.255.255.0

option 150 ip 192.168.1.1

default-router 192.168.1.1

Therefore, the short answer to your question would be yes, you need to have a 26xxXM router. Otherwise, you can use the GNS3 that Justin suggested.

Also, the CME doesnt come with the router, it will need to be downloaded from CCO, and you need to verify that you are running a version of IOS that supports voice.

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

I was informed that any recent 26xx , 36xx router will have CME and can be verified by looking into router#show telephony-service.

Thank you,

Community Member

Re: cisco IP phone 7960 test

Do I need to use any voice interface card on the 2600XM router to connect with the Cisco IP phone?

Re: cisco IP phone 7960 test

You only need to use a voice interface card if you plan on connecting to the PSTN. If not, and you just want to do VOIP, then you will not need any voice card. You will just need a router with an etherswitch card that has POE, or a POE capable switch. If your switch isnt POE capable, then you will need the power cube to power the phone.

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

Can you please list all cards that supports the following ,

1. PoE ethernet card for 2600XM router

2. Voice interface card to connect PSTN

3. Ethernet card for 2600XM to connect with PoE switch.

Thank you,

Re: cisco IP phone 7960 test

1. The etherswitch card part number is HWIC-4ESW. Not sure if this will be supported by 2600XM.

2. There are a variety of voice cards to connect to PSTN. Are you using analog POTS line, PRI, T1 CAS? The type of PSTN connection that you plan on using will determine what kind of voice card you need.

3. If your router has a built in ethernet port (which it should), then you wont need a special card to connect to the PoE switch. You can just use a straight through cable to connect the ethernet port on the router to the switch and you should be fine.

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

I am trying to go with the existing firmware on the IP phone 7960. Do I still need TFTP server, CME software and Firmware loading configuration?

Community Member

Re: cisco IP phone 7960 test

We will be using T1 or PRI connection.

Thank you

Re: cisco IP phone 7960 test

If you are using PRI, you will need a VWIC-1MFT-T1/E1. And yes, you will still need to configure the router as a TFTP server, you dont need a separate piece of hardware for this. Also, yes you will still need CME software in order for the phone to function correctly.

Community Member

Re: cisco IP phone 7960 test

Kenneth, can you please provide me some link to get WEb interface configuration details of IP phone 7960? I am remotly into the phone.

Re: cisco IP phone 7960 test

Well, once you get everything you need to get the CME running, the GUI files for the web interface are included with the software. You wont be able to do ANYTHING until you get the proper hardware. When you do get everything installed, you will simply browse to the IP address of the CME router (http://

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

Can I reset the IP phone to factory defaults? Once I reset the IP phone will I lose firmware on the IP phone? We are not sure about the service contract on these IP phone. How can I do factory defaults without losing firmware on the IP phone?

Thank you,

Re: cisco IP phone 7960 test

1. Yes

2. Yes

3. You can't

The CME software when you load it will have firmware loads for all of the phone models

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

We will be getting a Cisco Router with CME 4.1 loaded on it(router). Will it have firmware for IP phone 7960?

Thank you,

Re: cisco IP phone 7960 test

See my above post.

Hope that helped, if so please rate.

Community Member

Re: cisco IP phone 7960 test

How do I check that the Cisco Unity software is loaded into my router? Does it come along with the router voice image? I aslo need to setup voice mail. Do I need any additional hardware for that?

Thank you,

Re: cisco IP phone 7960 test

Siva,

Please reference the following link, along with the link I posted earlier, to answer any further questions you may have in reference to configuration and compatibility.

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_installation_and_configuration_guides_list.html

Thank you for the nice ratings, and have a nice day.

Hope that helped, if so please rate.

Re: cisco IP phone 7960 test

Hi Siva,

You will need a Cisco Unity Module to install in the router.

Either a AIM-CUE or NME-AIM Module will do.

The router will come shipped with a voice image.

You can run sh version to see if the module is recognized by the post.

sh inventory should also show this info.

Regards,

Justin

550
Views
75
Helpful
27
Replies
CreatePlease to create content