Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

cisco VG to PBX problem

Hi

I have coonectd my router via a wvic (E1 Qsig) to a pbx.

the pbx users can call my fxs ports and they can talk,but the problem is when I try to call them from FXS analoge telefone tp PBX users.. their phone will ring but I can not hear anythig and also when they pick up the phone no timeslot will be activated and therefore i can not here their voice.

please help me

4 REPLIES
New Member

Re: cisco VG to PBX problem

Could you post the following-

1. sh run

2. deb isdn q931 / deb voice ccapi in out

Subhrojyoti

New Member

Re: cisco VG to PBX problem

BX-VG#

*Oct 16 11:00:49.147: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Calling num 8

*Oct 16 11:00:49.147: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x16 is 0x0 0x0, Called num 2830

*Oct 16 11:00:49.151: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x008E

Sending Complete

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9838A

Exclusive, Channel 10

Progress Ind i = 0x8183 - Origination address is non-ISDN

Calling Party Number i = 0x0080, '8'

Plan:Unknown, Type:Unknown

Called Party Number i = 0x80, '2830'

Plan:Unknown, Type:Unknown

*Oct 16 11:00:49.243: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x808E

*Oct 16 11:00:49.247: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:00:49.271: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x808E

*Oct 16 11:00:49.275: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:00:49.283: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x808E

*Oct 16 11:00:49.287: ISDN Se0/0/0:15 Q931: TX -> STATUS pd = 8 callref = 0x008E

Cause i = 0x80E018 - Mandatory information element missing

Call State i = 0x01

*Oct 16 11:01:05.367: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x008E

Cause i = 0x8090 - Normal call clearing

*Oct 16 11:01:05.439: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x80

New Member

Re: cisco VG to PBX problem

Can you try this?

voice call send-alert > under global config

progress_ind alert enable 8 > under the voice dial-peer # pots configuration

Subhrojyoti

New Member

Re: cisco VG to PBX problem

hi

i have provided them before but nothing happend

the problem remains! :(

174
Views
0
Helpful
4
Replies