Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CISCO2921/K9 w/ PVDM3-64

Hi -

New SRST gateway I'm installing has PVDM3-64 installed. When booting the router I get the following warning:

Warning! DSPs1, 2,  in slot 0 are using non-default firmware from flash:

This is not recommended, the default version is 26.3.6

But when I do a show voice dsp detailed the installed DSP shows the correct firmware it says I should be using.

EOGrvMUSshawn01#show voice dsp detailed

DSP  DSP                DSPWARE CURR  BOOT                         PAK     TX/RX

TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT

==== === == ======== ========== ===== ======= === == ========= == ===== ============

----------------------------FLEX VOICE CARD 0 -----------------------------

                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending

LEGEND     : (bad)bad    (shut)shutdown  (dpend)download pending

DSP    DSP                 DSPWARE CURR  BOOT                         PAK   TX/RX

TYPE   NUM CH CODEC        VERSION STATE STATE   RST AI VOICEPORT TS ABRT PACK COUNT

====== === == ========= ========== ===== ======= === == ========= == ==== ============

SP2600 001 01 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 02 None         26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 03 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 04 None          26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 05 None         26.3.6 idle  idle      0  0                 0          0/0

SP2600 001 06 None          26.3.6 idle  idle      0  0                 0          0/0

EOGrvMUSshawn01#show inv | inc PVDM3      

NAME: "PVDM3 DSP DIMM with 64 Channels on Slot 0 SubSlot 4", DESCR: "PVDM3 DSP DIMM with 64 Channels"

PID: PVDM3-64          , VID: V01 , SN: FOC16311779

Any suggestions to why this warning message is showing and if it will cause problems is much appreciated!

Thanks,

Tom Fredericks      

5 REPLIES
Hall of Fame Super Silver

Re: CISCO2921/K9 w/ PVDM3-64

Do you have other firmware files defined on flash?

Can you post "sh flash"?

Sent from Cisco Technical Support iPhone App

New Member

CISCO2921/K9 w/ PVDM3-64

Not that I can see. Just have the default files that come with the router and the IOS bin.

EOGrvMUSshawn01#show flash

-#- --length-- -----date/time------ path

1         2903 Aug 14 2012 02:09:04 cpconfig-29xx.cfg

2      3000320 Aug 14 2012 02:09:16 cpexpress.tar

3         1038 Aug 14 2012 02:09:24 home.shtml

4       122880 Aug 14 2012 02:09:32 home.tar

5      1697952 Aug 14 2012 02:09:46 securedesktop-ios-3.1.1.45-k9.pkg

6       415956 Aug 14 2012 02:09:58 sslclient-win-1.1.4.176.pkg

7         2962 Aug 22 2012 15:01:38 -0

8     62759344 Aug 22 2012 15:17:08 c2900-universalk9-mz.SPA.150-1.M2.bin

9        14042 Aug 22 2012 15:22:36 -1

10       11901 Aug 24 2012 14:14:50 -2

11       14021 Aug 24 2012 14:35:16 -3

12       14021 Aug 24 2012 14:43:04 -4

188407808 bytes available (68079616 bytes used)

Hall of Fame Super Gold

CISCO2921/K9 w/ PVDM3-64

Update IOS and check again.

New Member

CISCO2921/K9 w/ PVDM3-64

Hi Paolo -

I have tried with two different IOS versions and gotten the same result.

c2900-universalk9-mz.SPA.150-1.M8.bin

c2900-universalk9-mz.SPA.150-1.M2.bin

Hall of Fame Super Gold

CISCO2921/K9 w/ PVDM3-64

Then if you no operational problem, you can ignore the message.

635
Views
0
Helpful
5
Replies
CreatePlease to create content