Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CME 4.0.2

Hello,

I have a 2801 with the cme ver 4.0.2.

I want to connect 7945 and 7937 conference station. I think the ios that supports the 7937 is ver 4.3.

I tried to install it but there was a problem in the pstn lines after one minute every telephone call was disconnected.

Could you please advice me what to do.

7 REPLIES

Re: CME 4.0.2

Well you can only upload the phone loads to the flash and then to the tftp.

New Member

Re: CME 4.0.2

Do you think that the conference station 7937g will work fine?

In he cisco website it is recommended that no version of ios below of 4.3 supports this model?

Have you tried it?

Thank you very much.

New Member

Re: CME 4.0.2

I tried to load the firmware of the 7937G station to the ccme ver 4.0.2 (2801)

but there was no such type of phone when i typed the command load:

CCME(config)#telephony-service

CCME(config-telephony)#load ?

12SP Select the firmware load file for 12SP+ and 30VIP phones

7902 Select the firmware load file for 7902

7905 Select the firmware load file for 7905

7906 Select the firmware load file for 7906

7910 Select the firmware load file for Telecaster 7910 phones

7911 Select the firmware load file for 7911

7912 Select the firmware load file for 7912

7914 Select the firmware load file for sidecar 7914

7920 Select the firmware load file for 7920

7931 Select the firmware load file for 7931

7935 Select the firmware load file for 7935 Conference Station

7936 Select the firmware load file for 7936

7941 Select the firmware load file for 7941

7941GE Select the firmware load file for 7941GE

7960-7940 Select the firmware load file for Telecaster 7960 & 7940 phones

7961 Select the firmware load file for 7961

7961GE Select the firmware load file for 7961GE

7970 Select the firmware load file for 7970

7971 Select the firmware load file for 7971

ATA Select the firmware load file for ATA

CCME(config-telephony)#

Is there any other way to load the new phones?

Also the file i downloaded is an .exe instead of .bin

Is it the correct extension ? I tried to extracted but couldn't.

New Member

Re: CME 4.0.2

The 7937G conference station is not supported on CME versions below 4.3 The links below should help you out regarding supported phones/firmware etc.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme43spc.htm

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme42spc.htm

Cheers

Frank

New Member

Re: CME 4.0.2

Accidental double post...

New Member

Re: CME 4.0.2

Thanks,

I downloaded 4.3 and I am trying now!!

New Member

Re: CME 4.0.2

Hello,

I upgraded the ios of the 2801 to c2801-ipvoicek9-mz.124-15.XZ.bin which has cme ver 4.3 But unfortunatelly, the conference station 7937G does not register.

I have also downloaded on the flash

the firmware of the 7937g: apps37sccp.1-2-1-0.bin.

I want to load from the telephony-service the firmware but i cannot there is no option.

load ....(there is no 7937 type).

Is it not supported as well?

the tftp command is there as well.

tftp-server flash:apps37sccp.1-2-1-0.bin

I tried ios c2801-ipvoicek9-mz.124-15.XZ1, ver cme 7.0 but I had a problem with PSTN lines after some secs when i place or receive a call it disconnects.

Is there any other command I should input?

218
Views
3
Helpful
7
Replies