Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CME 8.6 One Way Audio over PRI

Greetings,

I am having an audio issue after a power outage over the winter break.  I now have no incoming audio via CME 8.6 over our TW PRI.  We are using a 3945 running 15.1(4)M4 with a VWIC3-2MFT-T1/E1 and a PVDM3-128. ISDN seems fine and calls connect both ways but only outgoing audio works. No firewall in place, translation patterns seem fine, only one interface active, voip bind srcaddr is correct, only using G711U, all voip calls from CME to CUCM work fine. Its only calls routed out the PRI that have the problem. Telco has ran diags (remotely) and does not see a problem.

Possible DSP issue? What else can I check on my end?

Thanks

Global ISDN Switchtype = primary-ni

ISDN Serial0/0/0:23 interface

        dsl 0, interface ISDN Switchtype = primary-ni

    Layer 1 Status:

        ACTIVE

    Layer 2 Status:

        TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED

    Layer 3 Status:

        1 Active Layer 3 Call(s)

        CCB:callid=800B, sapi=0, ces=0, B-chan=23, calltype=VOICE

    Active dsl 0 CCBs = 1

    The Free Channel Mask:  0x803FFFFF

    Number of L2 Discards = 0, L2 Session ID = 1

    Total Allocated ISDN CCBs = 1

Jan  3 12:50:06.439: ISDN Se0/0/0:23 EVENT: process_pri_call: call id 0x800F, nu                                                                              mber 5127734599, Guid B11884E78124, speed 0, call type VOICE, redial No, CSM cal                                                                              l No, pdata Yes

Jan  3 12:50:06.439: ISDN Se0/0/0:23 Q931: Applying typeplan for sw-type 0xD is                                                                               0x2 0x1, Calling num 5122626544

Jan  3 12:50:06.439: ISDN Se0/0/0:23 Q931: Sending SETUP  callref = 0x008E callI                                                                              D = 0x800F switch = primary-ni interface = User

Jan  3 12:50:06.439: ISDN Se0/0/0:23 Q931: TX -> SETUP pd = 8  callref = 0x008E

        Bearer Capability i = 0x8090A2

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA98397

                Exclusive, Channel 23

        Progress Ind i = 0x8183 - Origination address is non-ISDN

        Calling Party Number i = 0x2180, '512XXXXXXX'

                Plan:ISDN, Type:National

        Called Party Number i = 0xA1, '512XXXXXXX'

                Plan:ISDN, Type:National

Jan  3 12:50:06.499: ISDN Se0/0/0:23 Q931: RX <- CALL_PROC pd = 8  callref = 0x8                                                                              08E

        Channel ID i = 0xA98397

                Exclusive, Channel 23

Jan  3 12:50:06.499: ISDN Se0/0/0:23 EVENT: process_rxstate: ces/callid 1/0x800F                                                                               calltype 2 CALL_PROCEEDING

Jan  3 12:50:07.479: ISDN Se0/0/0:23 Q931: RX <- ALERTING pd = 8  callref = 0x80                                                                              8E

        Progress Ind i = 0x8188 - In-band info or appropriate now available

Jan  3 12:50:07.479: ISDN Se0/0/0:23 EVENT: process_rxstate: ces/callid 1/0x800F                                                                               calltype 2 CALL_PROGRESS

Jan  3 12:50:16.911: ISDN Se0/0/0:23 Q931: RX <- CONNECT pd = 8  callref = 0x808                                                                              E

Jan  3 12:50:16.911: ISDN Se0/0/0:23 EVENT: process_rxstate: ces/callid 1/0x800F                                                                               calltype 2 CALL_CONNECT

Jan  3 12:50:16: %ISDN-6-CONNECT: Interface Serial0/0/0:22 is now connected to 5                                                                              127734599 N/A

Jan  3 12:50:16.911: ISDN Se0/0/0:23 EVENT: isdn_neighbor_update: NLCB->State 10

Jan  3 12:50:16.911: ISDN Se0/0/0:23 EVENT: isdn_neighbor_update: NLCB->State 10

Jan  3 12:50:16.911: ISDN Se0/0/0:23 EVENT: process_rxstate: ces/callid 1/0x800F                                                                               calltype 2 CALL_PROGRESS

Jan  3 12:50:16.911: ISDN Se0/0/0:23 Q931: TX -> CONNECT_ACK pd = 8  callref = 0                                                                              x008E

Hays3945#

1 REPLY
New Member

CME 8.6 One Way Audio over PRI

debug voip dialpeer in out. Show your dial peers better if you paste your voice settings on router

378
Views
0
Helpful
1
Replies
CreatePlease login to create content