Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CME Billing

Hi There !

How does the billing works on CME ? I'll buy a 2851 CME...

Does the billing infomation (CDR) stays in the Flash ? How much time ? Is it possible to get a report of extension ?

I'd like to see some screenshoots of CME configuration, do you have any link that shows CME web interface ?

Thanks.

Andrei.

  • IP Telephony
1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Red

Re: CME Billing

Hi Andrei,

Here is where the CDR logs are for CME;

show call history voice - Displays the call history table for voice calls.

To specify call detail record (CDR) storage time, use the dial-control-mib command, which has two sets of keyword and argument options. The max-size number option specifies the maximum size of the CDR event table. The valid range is from 0-500, and the default is 50. Setting the value to 0 disables the CDR feature.

The retain-timer number option specifies the length of time in minutes that entries will remain in the call history table. The valid range is from 0-2147483647 minutes, and the default is 15. Setting the value to 0 prevents any call history from being retained.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/managcme.html

Call Activity Monitoring and Call History Logging

The Cisco Unified CME GUI provides call history table information so that a network administrator can monitor the call history information for unknown callers and use this information to disallow calling activities based on select calling patterns. The call history log should be configured to perform forensics and accounting and allow the administrator to track down fraudulent calling patterns. Configure the following commands to log call activity and call history:

dial-control-mib retain-timer 10080

dial-control-mib max-size 500

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_implementation_design_guide_chapter09186a00805f07a8.html#wp1077193

Logging CDR to External Servers

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/managcme.html#wp1076118

The parsing of this info is the tough part :( You might want to look into Cisco Partner "Stonevoice" that has a nice application for doing up these reports/graphs etc;

http://www.stonevoice.com/Products/AccountingBilling/tabid/767/Default.aspx#o

Sorry, don't have any screenshots :(

Cisco Unified Communications Manager Express System Administrator Guide

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm.html

Cisco Unified CallManager Express Solution Reference Network Design Guide

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_implementation_design_guide_book09186a00805f05db.html

Hope this helps!

Rob

"May your heart always be joyful And may your song always be sung May you stay forever young " - Dylan
2 REPLIES
Hall of Fame Super Red

Re: CME Billing

Hi Andrei,

Here is where the CDR logs are for CME;

show call history voice - Displays the call history table for voice calls.

To specify call detail record (CDR) storage time, use the dial-control-mib command, which has two sets of keyword and argument options. The max-size number option specifies the maximum size of the CDR event table. The valid range is from 0-500, and the default is 50. Setting the value to 0 disables the CDR feature.

The retain-timer number option specifies the length of time in minutes that entries will remain in the call history table. The valid range is from 0-2147483647 minutes, and the default is 15. Setting the value to 0 prevents any call history from being retained.

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/managcme.html

Call Activity Monitoring and Call History Logging

The Cisco Unified CME GUI provides call history table information so that a network administrator can monitor the call history information for unknown callers and use this information to disallow calling activities based on select calling patterns. The call history log should be configured to perform forensics and accounting and allow the administrator to track down fraudulent calling patterns. Configure the following commands to log call activity and call history:

dial-control-mib retain-timer 10080

dial-control-mib max-size 500

From this doc;

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_implementation_design_guide_chapter09186a00805f07a8.html#wp1077193

Logging CDR to External Servers

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/managcme.html#wp1076118

The parsing of this info is the tough part :( You might want to look into Cisco Partner "Stonevoice" that has a nice application for doing up these reports/graphs etc;

http://www.stonevoice.com/Products/AccountingBilling/tabid/767/Default.aspx#o

Sorry, don't have any screenshots :(

Cisco Unified Communications Manager Express System Administrator Guide

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm.html

Cisco Unified CallManager Express Solution Reference Network Design Guide

http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_implementation_design_guide_book09186a00805f05db.html

Hope this helps!

Rob

"May your heart always be joyful And may your song always be sung May you stay forever young " - Dylan
New Member

Re: CME Billing

wow. there's a lot of information !

Thanks a lot.

Andrei.

303
Views
0
Helpful
2
Replies
This widget could not be displayed.