Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

CME Calling Number Display Malformed

Hi,

We have CME 4.2 running on a 2811 router, and when incoming local calls come in - the display on the ip phone is a strange variety of characters. I have included a screenshot (ip comm as I dont have a digital camera handy) and also the debug q.931. Does any have any ideas why this would display as so?

Unknown numbers show up as 'unknown' however.

THanks,

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

Hi,

Which exact IOS is this ? Do you need any specific 4.2 feature or can you use 12.4(11)XJ4 sthat is stable and has many bugs fixed ?

10 REPLIES
Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

Hi,

Which exact IOS is this ? Do you need any specific 4.2 feature or can you use 12.4(11)XJ4 sthat is stable and has many bugs fixed ?

Community Member

Re: CME Calling Number Display Malformed

I'm using Version 12.4(11)XW3.

This was happening to me on version 3.3 on a 2651 as well, so i dont think it's a CME issue.

I will download and test now. Any other ideas?

Thanks

Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

XW4 has also been released. I see funny characters on my IP communicator too at times, which version are you using ?

Community Member

Re: CME Calling Number Display Malformed

Version 2.0.2 of the Communicator. Its also on the phones (using load P0030800500).

Ive just replaced the image, and gone back to P0030800400 so will be able to test in a little while.

What is you incoming dial-peer, and Serial port set to?

Mine are:

!

dial-peer voice 1 pots

description ** PRI POTS Incoming dial-peer **

incoming called-number ....

direct-inward-dial

!

!

interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bchan-number-order ascending

no cdp enable

!

Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

Hi,

for this problem, the config really doesn't matter. There is FW 8.0(7) available for the phones, that you can try.

Community Member

Re: CME Calling Number Display Malformed

Well, strange things. after re-loading IOS to CME4.1 when I dial myself it comes up properly! The site is in Singapore, so need to wait until tomorrow to get someone to test properly but it looks like there may be an issue with CME4.2!

Will post results tomorrow night!

Thanks for your help though

Community Member

Re: CME Calling Number Display Malformed

I'm running into the exact same incoming call strange character issue.

CME 4.2 running on a 2811 router. The exact IOS image that I'm using:

c2800nm-advipservicesk9-mz.124-11.XW1.bin

I'm holding off on downgrading back to 4.1 so I tried downgrading the phone firmware. The firmware was SCCP 8-2-2SR2 and I tried the older SCCP 8-2-2SR1. That did not help.

Anyone find a resolution to this issue while remaining on 4.2?

Thanks,

- Nate

Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

Hi, can you try XW6?

There's a bazillion of bugs fixed from XW1.

'

Community Member

Re: CME Calling Number Display Malformed

I must have had one out of the bazillion. Thanks that resolved my issue! I was not sure I could upgrade the IOS when the CME files specifically called for XW1.

Hall of Fame Super Gold

Re: CME Calling Number Display Malformed

That was fast! The gui files IMHO are so poorly written that know little difference between CME XWhatever and a kitchen sink.

Thanks for the nice rating and good luck!

422
Views
5
Helpful
10
Replies
CreatePlease to create content