Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CME FXO getting busy after disconnecting the call

Hi

i am having a setup with cme ver 8.6  and 3 fxo lines .some time even all the lines are free also user will not be able to make the call  it will give busy tone that time i use to shut and no shut the fxo port it will work .Please help me how to resole the issue  . i here attached the config below

voice call send-alert

voice rtp send-recv

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none

h323

  h225 timeout setup 5

!

voice class codec 1

codec preference 1 g711ulaw

codec preference 2 g711alaw

!

voice class dualtone-detect-params 1

freq-max-deviation 20

cadence-variation 20

!

voice class custom-cptone UAE-CPTONE

dualtone disconnect

  frequency 400 405

  cadence 380 380 400 350 225 525

!

!

!

!

!

license udi pid CISCO2911/K9 sn FCZ1540700Z

hw-module pvdm 0/0

!

!

!

username admin password 0 cisco

!

redundancy

!

!

!

translation-rule 9

Rule 1 ^00 900

Rule 2 ^02 9

Rule 3 ^03 903

Rule 4 ^04 904

Rule 5 ^05 905

Rule 6 ^06 906

Rule 7 ^07 907

Rule 8 ^08 908

Rule 9 ^09 909

!

!

!

!

!

i

interface Embedded-Service-Engine0/0

no ip address

shutdown

!

interface GigabitEthernet0/0

description *** Voice Gateway ****

ip address 192.168.50.4 255.255.255.0

ip pim dense-mode

duplex auto

speed auto

h323-gateway voip interface

h323-gateway voip bind srcaddr 192.168.50.4

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface GigabitEthernet0/2

no ip address

shutdown

duplex auto

speed auto

!

ip forward-protocol nd

!

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip http path flash:

!

ip route 0.0.0.0 0.0.0.0 192.168.50.250

!

access-list 23 permit 10.10.10.0 0.0.0.7

voice-port 0/0/0

trunk-group FXOPORTS

translation-profile incoming incomming

translate calling 9

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CPTONE

supervisory dualtone-detect-params 1

input gain 14

compand-type a-law

cptone AE

timeouts call-disconnect 1

timeouts wait-release 1

connection plar opx 5000

shutdown

caller-id enable

!

voice-port 0/0/1

trunk-group FXOPORTS

translation-profile incoming incomming

translate calling 9

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CPTONE

supervisory dualtone-detect-params 1

input gain 14

compand-type a-law

cptone AE

timeouts call-disconnect 1

timeouts wait-release 1

connection plar opx 5000

caller-id enable

!

voice-port 0/0/2

trunk-group FXOPORTS

translation-profile incoming incomming

translate calling 9

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CPTONE

supervisory dualtone-detect-params 1

input gain 14

compand-type a-law

cptone AE

timeouts call-disconnect 1

timeouts wait-release 1

connection plar opx 5000

caller-id enable

!

voice-port 0/0/3

supervisory disconnect dualtone mid-call

supervisory custom-cptone UAE-CPTONE

supervisory dualtone-detect-params 1

input gain 14

compand-type a-law

cptone AE

timeouts call-disconnect 1

timeouts wait-release 1

connection plar opx 5001

description **** MANAGER DIRECT LINE ****

caller-id enable

1 ACCEPTED SOLUTION

Accepted Solutions
Green

CME FXO getting busy after disconnecting the call

Hi,

Also remove the compound type from your FXO analogue voice ports as this can cause issues.

The compound type is used for digital technology like ISDN/BRI

!

voice-port 0/0/0

no compand-type a-law

!

voice-port 0/0/1

no compand-type a-law

!

voice-port 0/0/2

no compand-type a-law

!

voice-port 0/0/3

no compand-type a-law

!

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
5 REPLIES
Hall of Fame Super Gold

CME FXO getting busy after disconnecting the call

Most likely, your custom cptone configuration is incorrect.

Green

CME FXO getting busy after disconnecting the call

Hi,

Also remove the compound type from your FXO analogue voice ports as this can cause issues.

The compound type is used for digital technology like ISDN/BRI

!

voice-port 0/0/0

no compand-type a-law

!

voice-port 0/0/1

no compand-type a-law

!

voice-port 0/0/2

no compand-type a-law

!

voice-port 0/0/3

no compand-type a-law

!

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
New Member

CME FXO getting busy after disconnecting the call

Hi

Thanks paolo

Do you have any sample config for CPtone  for UAEregion

Green

CME FXO getting busy after disconnecting the call

Raja,

Try this website

http://www.3amsystems.com/wireline/tone-search.htm

Select your country and tone

You can only search once a day or something like that so get it right 1st time

Regards,
Alex.
Please rate useful posts.

Regards, Alex. Please rate useful posts.
Hall of Fame Super Gold

CME FXO getting busy after disconnecting the call

You will need to record the tone and analyze.

I used to have a router in Dubai, but i think I've since lost its configuration.

1869
Views
0
Helpful
5
Replies
CreatePlease to create content