Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

cme how increse maximum participants

When i try initiate conference with 3 or 4 paricipants, third and fourth participants listen silent if sccp phone or listen music if sip phone

#show dspfarm all

SLOT   DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0      1   35.1.2   UP     N/A  FREE  conf    1      -         -         -
0      1   35.1.2   UP     N/A  FREE  conf    1      -         -         -

 

I think if  i increase maximum participants in conference profile this solve my problem

When i try change  profile i have message  profile oper state is up in progress already

#dspfarm profile 1 conference

(config-dspfarm-profile)#maximum conference-participants 8

(config-dspfarm-profile)#no shutdown

 profile oper state is up in progress already

How can i change participants in profile?

 

Thanks for help

1 ACCEPTED SOLUTION

Accepted Solutions

Hi,You need to do "no

Hi,

You need to do "no sdspfarm tag 1 confdsp1"

and

"sdspfarm tag 1 confprof1"

 

Then do "no sccp" followed by "sccp"

Manish

11 REPLIES

I do not see you shutting

I do not see you shutting down the dspfarm profile , shutdown the dspfarm profile first, make changes and do a no shut.

HTH

Manish

Community Member

I perform#dspfarm profile 1

Thanks for your answer

I perform

#dspfarm profile 1 conference

(config-dspfarm-profile)#shutdown

Disabling profile will disconnect active CONFERENCING calls,
do you want to continue ? [yes/no]yes

(config-dspfarm-profile)#maximum conference-participants 8
(config-dspfarm-profile)#no shutdown

(config-dspfarm-profile)#end

 

#show dspfarm all

Dspfarm Profile Configuration

 Profile ID = 1, Service = CONFERENCING, Resource ID = 1
 Profile Description :
 Profile Service Mode : Non Secure
 Profile Admin State : UP
 Profile Operation State : RESOURCE ALLOCATED
 Application : SCCP   Status : ASSOCIATION IN PROGRESS
 Resource Provider : FLEX_DSPRM   Status : UP
 Number of Resource Configured : 2
 Number of Resources Out of Service : 0
 Maximum conference participants : 8
 Codec Configuration: num_of_codecs:6
 Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required
 Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required
 Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required
 Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required
 Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required
 Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required


SLOT   DSP VERSION  STATUS CHNL USE   TYPE    RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED

0      1   35.1.2   UP     N/A  FREE  conf    1      -         -         -
0      1   35.1.2   UP     N/A  FREE  conf    1      -         -         -

Total number of DSPFARM DSP channel(s) 2

I want use conference with three and four participants simultaneously

But problem still exist (  

 

 

 

 

Can you share the 'show run'

Can you share the 'show run' and 'show sccp' from the CME. Also 'show sccp conn' for an active conference call.

Manish

 

Community Member

Current config in attach

Current config in attach

Community Member

i try initiate call between

i try initiate call between to Cisco 6921 IP phones

but command #show sccp connections shows me

Total number of active session(s) 0, and connection(s) 0

Community Member

When conference active

When conference active between three Cisco 6921 IP phones

#show sccp
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
        IPv4 Address: IP
        Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: IP, Port Number: 2000
                Priority: N/A, Version: 7.0, Identifier: 100
                Trustpoint: N/A

Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: TCP_CONN_ERROR
Active Call Manager: IP, Port Number: 2000
TCP Link Status: NOT_CONNECTED, Profile Identifier: 1
Reported Max Streams: 16, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED

 

#show sccp connections

Total number of active session(s) 0, and connection(s) 0

 

 

Hi,

Hi,

Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: TCP_CONN_ERROR

In your config, you have

 associate profile 1 register confprof1

and

 sdspfarm tag 1 confdsp1

Change the "sdspfarm tag 1 confdsp1" to  "sdspfarm tag 1 confprof1" and do a no sccp / sccp

Let us know if that fixes the issue.

Manish

 

Community Member

sorry i newbie in ciscome

sorry i newbie in cisco

me need perform:

#telephony-service

#no sccp

#sdspfarm tag 1 confprof1

#sccp

#end

I understand you correctly?

 

 

Hi,You need to do "no

Hi,

You need to do "no sdspfarm tag 1 confdsp1"

and

"sdspfarm tag 1 confprof1"

 

Then do "no sccp" followed by "sccp"

Manish

Community Member

Thank you very much!You

Thank you very much!
You helped me a lot!!!!!
Conference are now working!

 

I think this is solved in most settings conference station

 

 

That's good to know. Please

That's good to know. Please remember to rate all helpful posts and mark the discussion as solved if your query / issue has been answered / fixed.

Manish

154
Views
0
Helpful
11
Replies
CreatePlease to create content