Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CME parallel huntgroup.

Hi, I've configured some DN's as below:

ephone-dn 11 dual-line

number 202 no-reg primary

label 202

description 202

name 202

!

!

ephone-dn 12 dual-line

number 203 no-reg primary

label 203

description 203

name 203

!

!

ephone-dn 13 dual-line

number 204 no-reg primary

label 204

description 204

name 204

!

!

ephone-dn 14 dual-line

number 205 no-reg primary

label 205

description 205

name 205

!

!

ephone-dn 15 dual-line

number 206 no-reg primary

label 206

description 206

name 206

They work great. Im trying to impliment the following parallel hunt group:

voice hunt-group 1 parallel

pilot 203

list 204, 205, 206

final 207

timeout 20

But i get this message:

UC520(config-voice-hunt-group)#list 203, 204

Number 203 is not a valid voice register dn. Re-enter 'list.'

Any ideas?

Cheers

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: CME parallel huntgroup.

Hi, "voice hunt-group" is a command for SIP phones exclusively.

SCCP phones do not currently support parallel hunt-groups. Supposedly, they will in a future CME release.

You either use shared lines, or a TCL/IVR service that I wrote for the purpose:

http://pbevila.fastmail.fm/public/bcast.tcl

Hope this helps, please rate post if it does!

10 REPLIES
Hall of Fame Super Gold

Re: CME parallel huntgroup.

Hi, "voice hunt-group" is a command for SIP phones exclusively.

SCCP phones do not currently support parallel hunt-groups. Supposedly, they will in a future CME release.

You either use shared lines, or a TCL/IVR service that I wrote for the purpose:

http://pbevila.fastmail.fm/public/bcast.tcl

Hope this helps, please rate post if it does!

New Member

Re: CME parallel huntgroup.

damn, I knew it was too good to be true.

Cheers!

New Member

Re: CME parallel huntgroup.

Hi Paulo, im looking at your TCL script there. I can see that the first few lines are hashed out, and one line contains extension numbers in 'param destinations'

However I cant see param destination being called further down in the script, so does this mean they're not hashed out but just are variables?

cheers :)

Hall of Fame Super Gold

Re: CME parallel huntgroup.

Hi, hashed lines are comments and config examples.

Actual configuration is done with parameter commands under service.

New Member

Re: CME parallel huntgroup.

OK, im looking to impliment this script towards the end of the week on our piece of kit to give it a good testing.

My first question is... how do I make the system use the TCL script :) Do you have any install guide or config guide as I havent used TCL scripts before :(

Is it as simple as ftp'ing this script onto my UC520 box and then all phones will ring together? Forgive my poor TCL knowlege :(

Hall of Fame Super Gold

Re: CME parallel huntgroup.

Copy the file to the box, and configure as per example in the files itself.

New Member

Re: CME parallel huntgroup.

Ah im starting to get it now, so all I need to config on the box are :

application

service bcast flash:/IVR/bcast.tcl

param destinations 201,202,203 (or all the phones I want to ring)

# dial-peer voice 100 pots

# description broadcast hunt-group

# service bcast

# incoming called-number 5551234

Now Dial-peer voice 100 pots. Do I need this specific dial peer, or can I apply it to an exsiting dial peer? For example:

dial-peer voice 54 pots

description **Answers All Incoming Calls**

>>service bcast

>> incoming called-number .

direct-inward-dial

port 0/1/0

Thanks for your help mate, I very much appreciate it

Hall of Fame Super Gold

Re: CME parallel huntgroup.

Hi, under DP, you need service, incoming called-number, codec g711u and no vad. You don't need anything else.

New Member

Re: CME parallel huntgroup.

Ok, ill be giving this a go tomorrow, fingers crossed :)

Hall of Fame Super Gold

Re: CME parallel huntgroup.

I stand corrected, of course codec and vad do not apply to a pots DP.

These would apply when you configure a voip "loopback" DP in order to be able to access the service from ip phones as well.

590
Views
10
Helpful
10
Replies
CreatePlease to create content