Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CME Router with VIC-DID Config

Dear all,

Ip Phone extension use 4 digit (e.g. 8110). The CO provide 3 digit (i.e. 110) via the Direct Inward Dial Line.

What command should I configure on dial-peer and voice-port? And how to convert 3 digit from CO to 4 digit extension?

Thanks.

10 REPLIES
Hall of Fame Super Gold

Re: CME Router with VIC-DID Config

Under voice-port, configure signal and then the scheme used by telco.

Under dial-peer, configure direct-inward-dial, incoming called-number ... and the relevant port an a translation-profile

voice translation-profile adddigit

translate called 100

voice translation-rule 100

rule 1 // /8/

New Member

Re: CME Router with VIC-DID Config

Is the translation-profile on dial-peer is incoming or outoging? Is below config ok?

voice translation-rule 100

rule 1 // /8/

voice translation-profile adddigit

translate called 100

voice-port 1/0/0

signal did immediate

dial-peer voice 100 pots

translatioin-profile incoming adddigit

incoming called-number ...

direct-inward-dial

port 1/0/0

Thanks.

Hall of Fame Super Gold

Re: CME Router with VIC-DID Config

Yes, it looks ok to me.

I was under the impression that the translation wasn't even needed, because the DN's are matched by last digits, but I couldn't verify that yet.

Also may be you need an extra dot in 'icoming called-number", as probably it is applied afted the translation-profile trasformation.

New Member

Re: CME Router with VIC-DID Config

The DID doesn't work. When I dial in, I can see the DID port light up.

Attached is the debug vpm singal.

Hall of Fame Super Gold

Re: CME Router with VIC-DID Config

Hi,

Can you verify that the signal 'immediate' is correct? Looks to me the telco is not sending any digit, perhaps it is wink or other signaling needed.

New Member

Re: CME Router with VIC-DID Config

Since telco provide 3 digit. I setup a phone with 3 digit (ext. 857). I remove the translation profile on the dial-peer. I also try to test with three different did signalling.

ephone-dn 100

number 857

ephone 10

mac-address 001A.6D88.8581

button 1:100

voice-port 0/1/0

signal did (immediate/wink-start/delay-dial)

dial-peer voice 100 pots

incoming called-number 857

direct-inward-dial

port 0/1/0

Below is the debug vpm all for three different signal type.

New Member

Re: CME Router with VIC-DID Config

Sorry, I have a new finding. I found that there is no digit receive from the did line. When I create a translation rule to my extension 8110. it work. It seem that the telco do not forward any digit or my did port do not receive any digit.

voice translation-rule 101

rule 1 // /8110/

!

voice translation-profile adddigit

translate called 101

dial-peer voice 82 pots

translation-profile incoming adddigit

incoming called-number ...

direct-inward-dial

port 1/0/0

How can I make sure if my did port is ok and it is telco problem?

Thanks.

Hall of Fame Super Gold

Re: CME Router with VIC-DID Config

Yes, that is what I was to tell you. No digits are passed. I'm not sure how to troubleshoot this further, but just few days ago a guy on this forum reported a VIC-4FXS/DID to work 'like a champ'.

New Member

Re: CME Router with VIC-DID Config

7801 is one of ip phone extension. when i dial 33337800, the call can made to 7801.. but from debug... i can get digit for 80 from telco after the translation to 7801..

voice translation-rule 101

rule 1 // /7801/

!

voice translation-profile adddigit

translate called 101

!

voice-port 0/1/0

signal did wink-start

timing wink-wait 5000

timing wait-wink 5000

timing wink-duration 3000

dial-peer voice 100 pots

translation-profile incoming adddigit

incoming called-number ....

direct-inward-dial

port 0/1/0

I think it is some parameter setting for voice-port?

Please help.

Many thanks.

Hall of Fame Super Gold

Re: CME Router with VIC-DID Config

Hi,

the rule you have now will add 7801 to any incoming number. I think you need did-digit-length and

rule 1 // /8/

232
Views
0
Helpful
10
Replies
CreatePlease to create content