Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

CME setup.

I'm attempting to configure the Call Manager Express 4.1 on a 2901 router.  I have 2 Cisco IP Phone 7961G's.  My connection to the network backbone is via a Catalyst 3560-X-Series switch hosting the local DHCP and NAT'ing to the network backbone.  My question is concerning VLAN's and DHCP hosting.  Will I have better success with the router hosting the local DHCP and/or will creating a voice-VLAN on the designated ports for the phones back to the dedicated port on the router?

v/r,

Shane

Router Config:

_______________________________

Current configuration : 3918 bytes
!
! Last configuration change at 15:27:09 UTC Wed Apr 11 2012 by router
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname router
!
boot-start-marker
boot-end-marker
!
!
logging buffered 51200 warnings
!
no aaa new-model
!
no ipv6 cef
ip source-route
ip cef
!
!
!
!
!
no ip domain lookup
ip domain name yourdomain.com
multilink bundle-name authenticated
!
!
!
!
!
!
!
voice-card 0
!
!
!
voice service voip
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
sip
  registrar server expires max 1200 min 300
!
!
voice register global
mode cme
!
!
!
!
license udi pid CISCO2901/K9 sn XXXXXXXXXXXXXXXXX
hw-module pvdm 0/0
!
!
!
!
redundancy
!
!
!
!
!
!
interface Loopback1
no ip address
!
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address XXX.XXX.XXX.XXX 255.0.0.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
!
interface GigabitEthernet0/1
description $ES_LAN$
ip address XXX.XXX.XXX.XXX 255.255.255.0
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
!
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
ip nat inside source static XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
ip nat outside source static XXX.XXX.XXX.XXX XXX.XXX.XXX.XXX
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
ip route XXX.XXX.XXX.XXX 255.255.255.0 XXX.XXX.XXX.XXX
!
access-list 23 permit XXX.XXX.XXX.XXX 0.0.0.255
access-list 100 permit ip host XXX.XXX.XXX.XXX any
!
!
!
control-plane
!
!
!
!
mgcp profile default
!
!
!
!
!
gatekeeper
shutdown
!
!
!
line con 0
login local
line aux 0
line vty 0 4
access-class 23 in
exec-timeout 0 0
privilege level 15
password XXXXXXXXXXXXXX
login
transport input telnet ssh
line vty 5 15
access-class 23 in
exec-timeout 0 0
privilege level 15
password XXXXXXXXXXXXXXX
login
transport input telnet ssh
!
scheduler allocate 20000 1000
end

router#

Switch Config:

_____________________________________________

Building configuration...

Current configuration : 6307 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname switch
!
boot-start-marker
boot-end-marker
!
enable secret XXXXXXXXXXX
enable password XXXXXXXX
!
!
!
no aaa new-model
clock timezone UTC -5
clock summer-time UTC recurring
system mtu routing 1500
no ip dhcp conflict logging
!
ip dhcp pool voice
   network XXX.XXX.XXX.XXX 255.255.255.248
!
!
no ip domain-lookup
!
!
crypto pki trustpoint TP-self-signed-494936704
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-494936704
revocation-check none
rsakeypair TP-self-signed-494936704
!
!
spanning-tree mode pvst
spanning-tree extend system-id
auto qos srnd4
!
!
!
!
vlan internal allocation policy ascending
!
!
!
interface FastEthernet0
no ip address
shutdown
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface GigabitEthernet0/3
!
interface GigabitEthernet0/4
!
interface GigabitEthernet0/5
!
interface GigabitEthernet0/6
!
interface GigabitEthernet0/7
!
interface GigabitEthernet0/8
!
interface GigabitEthernet0/9
!
interface GigabitEthernet0/10
!
interface GigabitEthernet0/11
!
interface GigabitEthernet0/12
!
interface GigabitEthernet0/13
switchport access vlan 10
!
interface GigabitEthernet0/14
switchport access vlan 10
!
interface GigabitEthernet0/15
switchport access vlan 10
!
interface GigabitEthernet0/16
switchport access vlan 10
!
interface GigabitEthernet0/17
switchport access vlan 10
!
interface GigabitEthernet0/18
switchport access vlan 10
!
interface GigabitEthernet0/19
switchport access vlan 10
!
interface GigabitEthernet0/20
switchport access vlan 10
!
interface GigabitEthernet0/21
switchport access vlan 10
!
interface GigabitEthernet0/22
switchport access vlan 10
!
interface GigabitEthernet0/23
switchport access vlan 10
!
interface GigabitEthernet0/24
switchport access vlan 10
!
interface GigabitEthernet1/1
!
interface GigabitEthernet1/2
!
interface GigabitEthernet1/3
!
interface GigabitEthernet1/4
!
interface TenGigabitEthernet1/1
!
interface TenGigabitEthernet1/2
!
interface Vlan1
ip address XXX.XXX.XXX.XXX 255.255.255.0
!
interface Vlan10
ip address XXX.XXX.XXX.XXX 255.0.0.0
!
interface Vlan20
no ip address
!
ip http server
ip http secure-server
ip sla enable reaction-alerts
snmp-server community
snmp-server community
snmp-server location XXXXXX
snmp-server contact XXXXXXXXXXX
!
!
line con 0
exec-timeout 1440 0
line vty 0 4
exec-timeout 0 0
password XXXXXXXXXXX
login
line vty 5 15
exec-timeout 0 0
password XXXXXXXXXXX
login
!
!
monitor session 1 source interface Gi0/12
monitor session 1 destination interface Gi0/23
end

switch#

Everyone's tags (2)
1 REPLY
Hall of Fame Super Gold

CME setup.

Wrong forum, try "ip telephony". You can move the post using the control panel on the right.

436
Views
0
Helpful
1
Replies
CreatePlease login to create content