CME version 2811 CLI

Claudio Quiroz Cabello · ‎08-07-2012

Hello friends,

I have one Cisco 2811, version IOS 12.4(15)X. I wrote: "show telephony service all", "show version" and "show ccm-manager", but 2811 didn´t show version CME.

How can i know version CME throught CLI command or another form?

Thanks for you help...

paolo bevilacqua · ‎08-07-2012

You need IOS with voice support to configure CME. Then, you can issue show commands.

Claudio Quiroz Cabello · ‎08-08-2012

I understand Paolo, but how can i get version CME in 2811 router?

What can i do?

arunkum3 · ‎08-08-2012

Hi Claudio,

The command is :

show telephony-service all

You are missing the hyphen between "telephony" and "service".

Also there are two things that should be done before the above command shows you the :

1.) As Paolo pointed out, the IOS should support voice. Paste the show version output.

2.) configure "telephony-service" first on the router. This will bring up the virtual DSP on the router. Optionally you can configure max-dn and max-ephone commands.

Let me know if this helps.

Regards,

Arun Kumar

Please rate useful posts.

Claudio Quiroz Cabello · ‎08-08-2012

Arun.

I pasted you output... I don´t know why... Any idea please?

CME-IMDEX>

CME-IMDEX>show telephony-service

^

% Invalid input detected at '^' marker.

CME-IMDEX>show telephony-service all

^

% Invalid input detected at '^' marker.

CME-IMDEX>show run

^

% Invalid input detected at '^' marker.

CME-IMDEX>show version

Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(15)X

Z, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Fri 11-Apr-08 17:50 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

CME-IMDEX uptime is 3 weeks, 5 days, 1 hour, 2 minutes

System returned to ROM by power-on

System restarted at 16:08:52 gmt Sat May 12 2012

System image file is "flash:c2800nm-advipservicesk9-mz.124-15.XZ.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.50) with 239616K/22528K bytes of memory.

Processor board ID FTX1218A1EW

2 FastEthernet interfaces

31 Serial interfaces

1 terminal line

1 Channelized E1/PRI port

1 Virtual Private Network (VPN) Module

1 cisco Integrated Service Engine(s)

Cisco Unity Express 3.1.1 in slot 1

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

125440K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

paolo bevilacqua · ‎08-08-2012

You need to do 'enable' first, and input the corresponding password.

Note: please refrain from half-scale rating posts that are 100% correct, and made with the will to help.

Claudio Quiroz Cabello · ‎08-08-2012

Then i should put privilege mode first Paolo?

paolo bevilacqua · ‎08-08-2012

Enable == privileged.

Claudio Quiroz Cabello · ‎08-08-2012

Thankyou very much Paolo and Arun....