Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

Conecct E1 R2 to a router 2851

Hi, I want connect a E1 to a router 2851 with CUCME 4.1, but whenever I dial some DID (after configure the card VWIC2-2MFT-T1/E1), the calls are not routed to the extensions, the first thing the router do is give me a tone of reorder to dial the extension and then the call is routed to the extension

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

conf t

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

Noete you can group the analog ports under trunk group, that will allow you to collapse most DPs under a single one.

14 REPLIES
Community Member

Re: Conecct E1 R2 to a router 2851

Do you have more than one Pots dial-peers configured?

If so ensure you have incoming called-number. & direct-inward-dial on the dial-peer you expect inbound calls to use.

Community Member

Re: Conecct E1 R2 to a router 2851

hi, thanks for your answer...

yes, I have more dial-peer's pots, I erase thats but the problem continue.

I attach the actual configuration, thanks

Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

conf t

dial-peer voice 1 pots

incoming called-number .

direct-inward-dial

Noete you can group the analog ports under trunk group, that will allow you to collapse most DPs under a single one.

Community Member

Re: Conecct E1 R2 to a router 2851

ok, i will try this, and after I tell you the result, thanks

Community Member

Re: Conecct E1 R2 to a router 2851

Hi, me again.

the problem to receive calls, was solved (thank's for yours councils), but I have a new problem.

Now, I can not make calls to PSTN from PBX. PBX are a Panasonic 1232 with E1 card

Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

Need to see configuration. Do not send full configuration, only voice related, do not use attachments if possible.

Please remember to rate useful posts with the scrollbox below.

Community Member

Re: Conecct E1 R2 to a router 2851

This the configuration

----------------------

controller E1 0/2/0

framing NO-CRC4

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

country telmex

category 2

answer-signal group-b 1

caller-digits 4

dnis-digits min 4 max 4

ani-digits min 0 max 20

dnis-complete

description TRONCALES DIGITALES AXTEL

!

controller E1 0/2/1

framing NO-CRC4

clock source internal

ds0-group 0 timeslots 1-15,17-20 type r2-digital r2-compelled ani

cas-custom 0

country telmex use-defaults

category 2

answer-signal group-b 1

timer interdigit incoming 2500

dtmf timer inter-digit 2500

description TRONCALES PANASONIC

!

!

voice-port 0/2/0:0

cptone MX

!

voice-port 0/2/1:0

cptone MX

timeouts interdigit 3

timing digit 400

!

dial-peer voice 1 pots

incoming called-number 55508916..

direct-inward-dial

port 0/2/0:0

!

dial-peer voice 2 pots

description PBX

destination-pattern 16..

direct-inward-dial

port 0/2/1:0

forward-digits all

!

dial-peer voice 3 pots

corlist outgoing ll-loc

description LLAMADAS LOCAL

destination-pattern 9........

direct-inward-dial

telephony-service

service dnis overlay

user-locale ES

network-locale ES

time-zone 9

time-format 24

date-format yy-mm-dd

dialplan-pattern 1 55508916.. extension-length 4 extension-pattern 14..

max-conferences 2 gain -6

moh twenty.au

transfer-system full-consult

--------

thanks

Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

Is the E1 to PBX up ? Check show controllers E1.

Is the PBX ready to receive 4 digits beginning with 16 ?

If yes to both questions, take "debug vpm signal" with "term mon" whe dialing 16xx.

Community Member

Re: Conecct E1 R2 to a router 2851

Sorry, I think not explain me good

When I try make a call to outside, the router give me dial tone, however if I dial any digit sequence, router only catch first digit and ignore the rest of digits

Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

Explain which calls work, and which ones do not. Check controllers also.

Community Member

Re: Conecct E1 R2 to a router 2851

One more time, s

orry, my english is not very well

I try connect the PBX (Panasonic 1232) to a router Cisco 2851 (with CCME 4.1) using card VWIC2-2MFT-T1/E1.

Incoming calls (Router to PBX) are completed succesful, but outgoing calls (PBX to Router) are not completed.

When I try make a call (from PBX), I hear dial tone and saw with the "show voice call summary" command that one line is goes off hook, then I start press digit, only the first digit is understand, the other digits are showed incorrectly (example 4#, or #) so the call is not complete.

What does you mean with check controllers, I don't understand???

I attach the debug file

Community Member

Re: Conecct E1 R2 to a router 2851

This is ended

I configure the route of the calls to the interface appropriate. Thanks for your help

Community Member

Re: Conecct E1 R2 to a router 2851

Hello there. I have a similar issue. Could you post the commands you used to solve you issue ?

Regards

Hall of Fame Super Gold

Re: Conecct E1 R2 to a router 2851

Please open new thread for a new problem, describe the problem in detail and include the relevant configuration.

560
Views
0
Helpful
14
Replies
CreatePlease to create content