Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Conference Resource

Hi There,

I'm trying to configure a CME dsp for conference...

I did this config:

---

R_JCB_22#sh run | begin scc

sccp local GigabitEthernet0/0

sccp ccm 10.2.41.22 identifier 1

sccp

!

sccp ccm group 1

bind interface GigabitEthernet0/0

associate ccm 1 priority 1

associate profile 1 register confdsp1

keepalive retries 5

!

dspfarm profile 1 conference

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

maximum sessions 8

associate application SCCP

---

And here is the status:

---

R_JCB_22#show sccp

SCCP Admin State: UP

Gateway IP Address: 10.2.41.22, Port Number: 2000

IP Precedence: 5

User Masked Codec list: None

Call Manager: 10.2.41.22, Port Number: 2000

Priority: N/A, Version: 3.1, Identifier: 1

Conferencing Oper State: ACTIVE - Cause Code: NONE

Active Call Manager: 10.2.41.22, Port Number: 2000

TCP Link Status: CONNECTED, Profile Identifier: 1

Reported Max Streams: 64, Reported Max OOS Streams: 0

Supported Codec: g711ulaw, Maximum Packetization Period: 30

Supported Codec: g711alaw, Maximum Packetization Period: 30

Supported Codec: g729ar8, Maximum Packetization Period: 60

Supported Codec: g729abr8, Maximum Packetization Period: 60

Supported Codec: g729r8, Maximum Packetization Period: 60

Supported Codec: g729br8, Maximum Packetization Period: 60

Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30

---

but when I try to use the softkey CONFRN in ip phone it returns a message: not avaliable line (I set that to portuguese)...

Any help ?

Thanks.

Andrei.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: Conference Resource

You need to configure confernece Ephone-dns as descirbed in the CME config guide. This is a very common omission.

HTH,

Chris

6 REPLIES
Hall of Fame Super Silver

Re: Conference Resource

You need to configure confernece Ephone-dns as descirbed in the CME config guide. This is a very common omission.

HTH,

Chris

New Member

Re: Conference Resource

..Ok.... now I'm embarrassed...

:)

It was missing a dual line..

ephone-dn 1 dual-line

number 9000

Thanks.

Andrei.

New Member

Re: Conference Resource

Hi Chris,

Could you please refer some document explaining the command "conference Ephone-dns"

Regards,

Ashish

Hall of Fame Super Silver

Re: Conference Resource

New Member

Re: Conference Resource

Hi Chris,

thanks for your reply. But I couldn't find "conference ephone-dns" any where in the CME Sys Admin guide.

I found the following commands only with respect to conference:

conference {ad-hoc | meetme}

conference add-mode [creator]

conference admin

conference drop-mode [creator | local]

conference hardware

I apologies for my lack of understanding but want to know if this command really exist or is IOS specific(available in specific IOS only). If so let me know the IOS details.

Million apologies if I failed to understand command properly.

Regards,

Ashish

Hall of Fame Super Silver

Re: Conference Resource

My apologizes I did not mean to lead you in the wrong direction, there is no "conference ephone-dn" command, you configure regular ephone-dn for conferencing:

To configure extension numbers for multi-party ad hoc and meet-me ad hoc conferencing, based on the maximum number of conference participants you configure, perform the following steps. Ad hoc conferences require four extensions per conference, regardless of how many extensions are actually used by the conference parties.

i.e.

ephone-dn 63 dual-line

number 8887

conference meetme

preference 3

!

!

ephone-dn 64 dual-line

number 8889

name Conference

conference ad-hoc

no huntstop

HTH,

Chris

150
Views
5
Helpful
6
Replies