Configure allowance of certain dial-peers for outgoing calls.

[Edson Vuma]

Hi, guys.

I have a CUCME environment and a couple of users on it.

I have certain dial peers already configured.

And I need to configure on certain IP Phone to use ONLY one dial peer for OUTGOING calls.

Others will still be using all dial-peers.

Can you show the commands here I have to insert on the CUCME?

Warm regards

[Suresh Subramanian]

Hello Edson,

you may need to configure CoR list for the ephone-DNs & for the dial-peers. Please go through these documents on how to configure it.

http://knightfoo.wordpress.com/2012/09/11/call-manager-express-class-of-restriction-cor-lists/

http://www.cisco.com/c/en/us/support/docs/voice/call-routing-dial-plans/42720-configuring-cor.html

//Suresh

Please rate all the helpful answers

[Edson Vuma]

Hi, Suresh..

Let me check it. Thanks

Regards

[Shashank Awasthi]

if you want to restrict the usage of outgoing dial-peers then Co- list is the only option. Can you give us your running configuration with an example of your requirement.

[Edson Vuma]

Hi,

Again....I want to add a third dial-peer with the same configs as dial-peer voice 2 pots EXCEPT the port....it must be port 0/0/0:15 and must be used only by...for example, the ephone-dn on the sh run below.

sh run (relevant configs)

dial-peer cor custom
 name locals
 name emergencies
 name mobiles
 name internationals
!
!
dial-peer cor list outbound-general
 member locals
 member emergencies
 member mobiles
 member internationals
!
dial-peer cor list outbound-except-one
 member locals
 member emergencies
 member internationals
!
dial-peer cor list call-emergencies
 member emergencies
!
dial-peer cor list call-locals
 member locals
!
dial-peer cor list call-internationals
 member internationals
!
dial-peer cor list call-mobiles
 member mobiles

!

!
dial-peer voice 1 pots
 corlist outgoing call-locals
 description Nacionais e Locais
 destination-pattern 92[13-9]......
 port 0/0/0:15
 forward-digits 8
!
dial-peer voice 2 pots
 corlist outgoing call-mobiles
 description Moveis ou Celulares
 destination-pattern 98[246].......
 port 0/1/0
 forward-digits 9
!
dial-peer voice 4 pots
 corlist outgoing call-internationals
 description Internacionais
 destination-pattern 900T
 port 0/0/0:15
 prefix 00
!
dial-peer voice 5 pots
 description Emergencia
 destination-pattern 91..
 port 0/0/0:15
 forward-digits 8
!

!

ephone-dn  13  dual-line
 number 13 secondary 21359013
 label Test_Phone
 description Test_Phone
 name _Test_Phone
 corlist incoming outbound-except-one
!

[Suresh Subramanian]

Hello Edson,

can you try the below config and let me know if it works as expected?

1) add "member isdn" under custom corlist & call-mobiles corlist

2) create the 'dial-peer voice 3 pots' like below and assign corlist call-mobiles and preference 0

dial-peer voice 3 pots
 corlist outgoing call-mobiles
 description Moveis ou Celulares
 destination-pattern 98[246].......
preference 0
 port 0/0/0:15
 forward-digits 9

3) add the command "preference 1" under dial-peer 2

4) on 'ephone-dn  13' change the corlist to 'corlist incoming call-mobiles' instead of 'outbound-except-one'

please test this and let me know how it works.

//Suresh

Please rate all the helpful posts

[Edson Vuma]

Hi, Suresh....

I managed to do it.

Now I wanted to make it possible to separate the outgoing calls for SAME destination-patterns.

For a specific ephone-dn, use a different dial-peer (another port) and other ephones remaining using the same dial-peer...for the same destination-pattern.

Any help?

Regards

/EV