Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Configuring E1

Have Vwic-wmft-e1. Controller shows down/down with increasing line code violations. Have verified framing /coding/isdn switch type with vendor. Card has AL and CD lights on (yellow and green). shut /no shut does nothing. Site is in India, if that helps. Using no-crc4/hdb3. CM is 6.11

7 REPLIES
New Member

Re: Configuring E1

Hi,

This is what we have set-up for a E1 in the UK -

sh contr e1

E1 0/0/0 is up.

Applique type is Channelized E1 - balanced

Framing is CRC4, Line Code is HDB3, Clock Source is Line.

From the running-config

!

card type e1 0 0

!

isdn switch-type primary-net5

isdn voice-call-failure 0

!

voice-card 0

no dspfarm

!

controller E1 0/0/0

pri-group timeslots 1-31

!

interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

!

Your ISDN switch-type will probably be different. If you have a sh run. show isdn stat, sh contr e1 - that would be handy.

James

New Member

Re: Configuring E1

Thanks for your response. Here are the requested files. What troubles me is that when I use a crossover, I get the CD light. Replaces it with a Cat5, CD light goes off, but either way, no status changes on controller

E1 0/0/0 is down.

Applique type is Channelized E1 - balanced

Receiver has loss of frame.

alarm-trigger is not set

Version info Firmware: 20060623, FPGA: 20, spm_count = 0

Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.

CRC Threshold is 320. Reported from firmware is 320.

INDELNRT301#sho isdn stat

Global ISDN Switchtype = primary-net5

%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply

ISDN Serial0/0/0:15 interface

dsl 0, interface ISDN Switchtype = primary-net5

L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003

Layer 1 Status:

DEACTIVATED

Layer 2 Status:

TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED

Layer 3 Status:

0 Active Layer 3 Call(s)

Active dsl 0 CCBs = 0

The Free Channel Mask: 0x00000000

Number of L2 Discards = 0, L2 Session ID = 1

--More--

INDELNRT301#sho run

Building configuration...

Current configuration : 3484 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

!

network-clock-participate wic 0

network-clock-select 1 E1 0/0/0

!

!

ip cef

!

!

no ip domain lookup

!

isdn switch-type primary-net5

!

voice-card 0

dspfarm

dsp services dspfarm

!

!

!

!

!

!

!

!

!

!

!

controller E1 0/0/0

framing NO-CRC4

pri-group timeslots 1-31 service mgcp

!

controller E1 0/0/1

shutdown

framing NO-CRC4

Interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

Voice Port 0/0/0:15

!

ccm-manager fallback-mgcp

ccm-manager redundant-host 10.5.139.197

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server 10.5.139.196

ccm-manager config

!

mgcp

mgcp call-agent 10.5.139.196 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp ip qos dscp cs3 signaling

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp rtp payload-type g726r16 static

mgcp bind control source-interface Loopback99

mgcp bind media source-interface Loopback99

!

mgcp profile default

!

!

line con 0

line aux 0

line vty 0 4

!

scheduler allocate 20000 1000

!

end

Silver

Re: Configuring E1

Check out this link:

http://www.cisco.com/en/US/tech/tk713/tk628/technologies_tech_note09186a00800f99bb.shtml#linecode

Excessive LCV are normally caused by either config or line issues. As James' mentions are you using the correct ISDN switch type. I've configured an E1 in India before and the config is the same as the UK.

New Member

Re: Configuring E1

Hi,

There may be a few commands that may need to be tweaked, nut l would contact your Telco as Layer 1 is showing as de-activated.

Global ISDN Switchtype = primary-net5

ISDN Serial0/0/0:15 interface

dsl 0, interface ISDN Switchtype = primary-net5

Layer 1 Status:

ACTIVE

New Member

Re: Configuring E1

If your E1 controller is in ?down/down" state, most likely you have a physical problem with the link. Confirm with your provider that they have all the same parameters as you configure in term of Framing and Linecode. In the lab, when you have wrong Framing/Linecoding, the controller will be down, but the moment I configure correct parameters, controller comes to up/up state even without "isdn switching" and PRI-DS0 configured.

Re: Configuring E1

In CUCM, if my provider has the following:

ISDN Switch Type - ETSI

.Line Coding - hdb3

.Framing - crc-4

I do not have these options on the MGCP for the gateway in CUCM. Only B8z3 or AMI.

How does this work in Taiwan then? I cant get my physical layer up

New Member

Re: Configuring E1

The {ISDN Switch Type - ETSI

.Line Coding - hdb3

.Framing - crc-4 ) is an E1 configuration.

Hi tcatlinins,

You may have a card type command set to T1.

Thats why you only see he B8zs which is a T1 config.

You may need to set the card type command

card type e1 slotno.

397
Views
0
Helpful
7
Replies