Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Configuring multiple MSN Numbers on BRI Interface

Hi everyone,

I've got an ISDN line with around 8 MSN numbers connecting to my BRI 0/0/0 interface.

I'm trying to configure the interface to answer only specific MSN numbers, but can only find the option to answer up to 2 numbers using isdn answer1 <number1> & isdn answer2 (number2).

Any idea how this can be done?

Any help is much appreciated.

Regards,

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

voice translation-rule 10

rule 1 reject /5551234/

voice translation-profile fxo-in

translate called 10

voice-port x/y

translation-profile incoming fxo-in

18 REPLIES
Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

You can use a voice translation-profile with rule to reject calls to the number you do not want to answer, under the voice-port or incoming DP.

hope this helps, please rate post if it does!

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

bevilacqua,

Thanks for your reply.

Can you please offer an example config that I can use to try it out ?

Thank you.

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

voice translation-rule 10

rule 1 reject /5551234/

voice translation-profile fxo-in

translate called 10

voice-port x/y

translation-profile incoming fxo-in

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

I've tried the suggested configuration but unfortunately the call still rings on the secretary's phone.

Here's what I've added:

!

!

voice translation-rule 2

rule 1 reject /23105551234/

!

!

voice translation-profile dropmsn

translate calling 2

translate called 2

!

!

voice-port 0/0/1

translation-profile incoming dropmsn

compand-type a-law

cptone GR

connection plar 49

bearer-cap Speech

!

I've also performed a test voice translation and it verifies that the call is blocked on rule 1.

Any ideas ?

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Do not use connection plar.

Instead, assign the number you want to answer as secodary for the ephone. And, check with "debug isdn q931" and "term mon" that the called number is exactly the same you want to reject.

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

I'm left a bit puzzled by your last response.

ext.49 refers to a pilot hunt list:

!

ephone-hunt 1 sequential

pilot 49

list 30, 50

timeout 10, 10

description Huntgroup-Sec->Everyone

!

Can you please provide an example of your suggestion to help make it a bit clearer for me ?

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

pilot 49 secondary 23105551234

or simply

pilot 23105551234

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

I'm still having problems blocking the msn number I want. Here's the complete relevant configuration, perhaps you can point me as to where I've incorrectly configured the system:

!

voice translation-rule 2

rule 1 reject /23105551234/

!

!

voice translation-profile dropmsn

translate calling 2

translate called 2

!

!

voice-port 0/0/1

translation-profile incoming dropmsn

compand-type a-law

cptone GR

bearer-cap Speech

!

!

ephone-hunt 1 sequential

pilot 49 secondary 23105551234

list 30, 50

timeout 10, 10

description Huntgroup-Sec->Everyone

!

Do I also need a dial-peer for the above to work as I didn't use any previously due to the 'connection plar 49' command.

Many thanks,

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Well, the "reject" number and the pilot secondary should be different, it is so in your actual configuration ? Also you don't need "translate calling".

You also need a DP with "incoming called number ." and "direct-inward-dial".

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

Thanks again for your input.

Can you verify the following configuration is correct as per instructions so I can give it a try? :

!

voice translation-rule 2

rule 1 reject /23105551234/

!

!

voice translation-profile dropmsn

translate called 2

!

!

voice-port 0/0/1

translation-profile incoming dropmsn

compand-type a-law

cptone GR

bearer-cap Speech

!

!

ephone-hunt 1 sequential

pilot 49 secondary 23105554321

list 30, 50

timeout 10, 10

description Huntgroup-Sec->Everyone

!

dial-peer voice 100 pots

destination-pattern 23105554321

incoming called number .

direct-inward-dial

port 0/0/1

Thank you.

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Seems fine ...

Note in reality cptone for BRi prots doesn't do anything, and beare-cap is often best left to default.

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Thanks Paolo,

I'll give it a try and let you know.

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

Your suggested configuration worked fine ! Many thanks for your patience and effort!

What I'd like to try out now is apply the above scenario to a voice gateway which routes all incoming calls to a CUCM system.

Here's what I've tried, but it didn't work on the remote system:

voice translation-rule 2

rule 1 reject /210500500/

!

voice translation-profile dropmsn

translate called 2

!

voice-port 0/0/0

translation-profile incoming dropmsn

!

!

dial-peer voice 400 voip

destination-pattern 210...

voice-class codec 1

session target ipv4:10.0.0.1

!

I tried also applying the translation-profile to the dp 400, but it didn't work.

In my previous example, we placed the number we wanted to ring, as a secondary on the hunt group's pilot (ephone-hunt 1 sequential

pilot 49 secondary 23105554321).

In this particular case, all incoming calls are routed to the call manager system.

Any ideas or suggestions ?

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Just configure a proper destination-pattern for the numbers you want, under DP 400.

Thanks for the nice rating and good luck!

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

Paolo,

Correct me if I am wrong, but I can only define one destination-pattern under each dial-peer, or use a pattern that matches all incoming numbers e.g destination-pattern 210....... (

In this new case, I've defined a generic pattern that catches all possible patterns I need (210500501, 210500502 e.t.c).

I don't understand what additions I must make to get the new scenario working;

An example based on the configuration below would be much appreciated:

voice translation-rule 2

rule 1 reject /210500500/

!

voice translation-profile dropmsn

translate called 2

!

voice-port 0/0/0

translation-profile incoming dropmsn

!

!

dial-peer voice 400 voip

destination-pattern 210......

voice-class codec 1

session target ipv4:10.0.0.1

!

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Seems fine, all numbers beginning with 210 and six more digits are sent to 10.0.0.1

New Member

Re: Configuring multiple MSN Numbers on BRI Interface

However, for some reason, 210500500 is not being rejected.

I also tried adding the translation-profile to the dial-peer you saw, but the system still answers 210500500!

Any further ideas ?

Hall of Fame Super Gold

Re: Configuring multiple MSN Numbers on BRI Interface

Check ouput of "debug isdn q931" with "term mon". Worst case you can route the number to a fake IP and it won't answer.

188
Views
10
Helpful
18
Replies