Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Configuring VWIC-1MFT-E1 on 2621XM router

I have a VWIC-1MFT-E1 in wic slot 1 of a 2621xm router running cisco IOS 12.4(17).

However I cannot confiure my pri-group under controller e1 command.

I cannot also do a show isdn status command.

Is there something I need to turn on?

Please assist.

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Hi,

You need DSP to configure card as PRI, and you don't have that.

You would need AIM-VOICE-30 that is a card that goes inside the router, or an NM-HD-xxx to host the VWIC. The first alternative is probably cheaper. The second one, when acquiring a network module supporting the latest generation DSP called PVDM2, would give you more feature and a longer technological lifespan.

Hope this helps, please rate post if it does!

12 REPLIES

Re: Configuring VWIC-1MFT-E1 on 2621XM router

You will probably find that you have not specified the card type.

Configure the card as follows, specifying the appropriate slot and wic of course:-

card type e1 1 1 (Slot/WIC)

HTH

Regards

Allan.

Community Member

Re: Configuring VWIC-1MFT-E1 on 2621XM router

I cannot seem to configure the card type. Under config it does not allow me to do that.

In sh run it shows controller e1 0/0

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Typically if the card-type is configured you will see the controller E1 in the configuration. If it was not configured, then there would be no controller.

Is there already a PRI group configured under the controller? Shutdown the controller remove the pri-group and reconfigure.

Pls post the config, and show diag to sanity check.

Regards

Allan.

Community Member

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Here is the sh run and sh diag

------------------ show running-config ------------------

Building configuration...

Current configuration : 1478 bytes

!

version 12.4

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname NSC_CITY_VG

!

boot-start-marker

boot-end-marker

!

enable secret 5

!

no aaa new-model

no network-clock-participate slot 1

no network-clock-participate wic 0

ip cef

!

!

!

!

isdn switch-type primary-net5

!

!

!controller E1 0/0

!

!!

interface FastEthernet0/0

ip address 192.168.24.2 255.255.255.0

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

ip forward-protocol nd

ip route 0.0.0.0 0.0.0.0 192.168.24.1

!

ip http server

no ip http secure-server

!

!

!

control-plane

!

!

!

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config server 192.168.2.11

ccm-manager config

!

mgcp

mgcp call-agent 192.168.2.11 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp modem passthrough voip redundancy

mgcp package-capability rtp-package

mgcp package-capability sst-package

mgcp package-capability pre-package

mgcp default-package dtmf-package

no mgcp package-capability res-package

no mgcp package-capability fxr-package

no mgcp timer receive-rtcp

mgcp sdp simple

no mgcp fax t38 ecm

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

!

!

!

line con 0

line aux 0

line vty 0 4

password

login

!

!

end

------------

NSC_CITY_VG#sh diag

Slot 0:

C2621XM 2FE Mainboard Port adapter, 3 ports

Port adapter is analyzed

Port adapter insertion time 02:13:10 ago

EEPROM contents at hardware discovery:

Hardware Revision : 4.0

PCB Serial Number : FFFF

Version Identifier :

Product (FRU) Number :

Chassis Serial Number : JHY0738K11M

Part Number : 73-7754-06

RMA History : 00

RMA Number : 0-0-0-0

Board Revision : C0

Deviation Number : 0-0

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 6D 41 04 00 C1 0B FF FF FF 46 46 46

0x10: 46 FF FF FF FF 89 FF FF FF FF CB 12 FF FF FF FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF C2 0B

0x30: 4A 48 59 30 37 33 38 4B 31 31 4D 82 49 1E 4A 06

0x40: 04 00 81 00 00 00 00 42 43 30 80 00 00 00 00 FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 1:

E1 (1 port) Multi-Flex Trunk WAN daughter card

Hardware revision 1.0 Board revision F0

Serial number 33070310 Part number 800-04475-03

FRU Part Number VWIC-1MFT-E1=

Test history 0x0 RMA number 00-00-00

Connector type PCI

EEPROM format version 1

EEPROM contents (hex):

0x20: 01 21 01 00 01 F8 9C E6 50 11 7B 03 00 00 00 00

0x30: 78 00 00 00 04 12 13 00 FF FF FF FF FF FF FF FF

NSC_CITY_VG#

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Firstly your configuration indicates that you are configuring your E1 through MGCP, therefore have you configured the gateway endpoint accordingly within CallManager, and also in the correct slot?

Looking at the 'show diag' I would expect to see controller 0/1 Slot 0 WIC 1.

How have you configured the gateway with hostname or IP address. I have noticed that have not configured a domain-name on the gateway, therefore ensure that if you use hostname for the gateway that you only use NSC_CITY_VG, and the CCM and resolve this.

If you have configured the endpoint correctly then I would expect CallManager to configured the pri-group. However are you attempting to reconfigure the pri-group as you have a fractional E1?

If this is not the case then try the following to download the config from CCM:-

1. remove all ccm-manager related commands.

2. configure 'network-clock-particpate wic 0'

3. reconfigure ccm-manager commands.

Regards

Allan.

Hall of Fame Super Gold

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Hi,

You need DSP to configure card as PRI, and you don't have that.

You would need AIM-VOICE-30 that is a card that goes inside the router, or an NM-HD-xxx to host the VWIC. The first alternative is probably cheaper. The second one, when acquiring a network module supporting the latest generation DSP called PVDM2, would give you more feature and a longer technological lifespan.

Hope this helps, please rate post if it does!

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Nice spot pbevilacqua, completely overlooked that aspect on the 'show diag'

Regards

Allan.

Community Member

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Thanks, I found out that My router did not have an AIM module on it. I assumed this would normally ship with it.

Community Member

Re: Configuring VWIC-1MFT-E1 on 2621XM router

I was wondering if there is a slot on the router where the AIM-Voice-30 card goes into?

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Take a look at the following link, it describes the various AIM cards supported, including the AIM-Voice-30.

http://www.cisco.com/en/US/products/hw/modules/ps2641/products_data_sheet09186a0080088753.html

You see that it is a daughter card installed internally on the hardware platform.

Regards

Allan.

Hall of Fame Super Gold

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Hi Allan,

there is no "card type" command for VWIC-xMFT-xx hardware, that is natively T1 or E1 depending on the version purchased.

The command is available for VWIC-xMFT-xx cards that are "universal".

Hall of Fame Super Gold

Re: Configuring VWIC-1MFT-E1 on 2621XM router

Fat fingers, I meant

The command is available for VWIC2-xMFT-xx cards that are "universal".

Thanks for the nice rating and good luck!

958
Views
4
Helpful
12
Replies
CreatePlease to create content