I would need your help in configuring our (SIP-)door-bell to ring/call (inbound) to predefined ephones.
We have a CME 9.1 on a 2900 Router - private IP: 10.200.200.14
We have a door-bell which is (successfully) registered as a SIP-Phone (IP: 10.200.200.16)
We already succeed in calling the doorbell with "700" from our inside-located ephones (we can hear/speak to the external Person at the doorbell)
CME-Configuration:
voice register global
mode cme
source-address 10.200.200.14 port 5060
max-dn 144
max-pool 24
authenticate register
hold-alert
tftp-path flash:
create profile sync 0057322453052382
voice register dn 2
number 700
name GSPA
no-reg
voice register pool 2
id mac 0012.3456.9298
number 1 dn 2
dtmf-relay sip-kpml
username 700 password ***********
codec g711ulaw
no vad
We have manually entered this dial-peer:
!
dial-peer voice 700 voip
description *** GSPA-Test ***
destination-pattern 700
session protocol sipv2
session target ipv4:10.200.200.14
incoming called-number 700
dtmf-relay sip-notify
codec g711ulaw
fax rate disable
no vad
!
------------------------------------
k2net-ipt01#sho voice register pool 2
Pool Tag 2
Config:
Mac address is 0012.3456.9298
Number list 1 : DN 2
Proxy Ip address is 0.0.0.0
Current Phone load version is VoIP Guard
DTMF Relay is enabled, sip-kpml
Call Waiting is enabled
DnD is disabled
Video is disabled
Camera is disabled
Busy trigger per button value is 0
keep-conference is enabled
registration expires timer max is 3600 and min is 60
username 700 password ext700
Lpcor Type is none
Transport type is udp
service-control mechanism is not supported
registration Call ID is 905639817
Registration method: per line
Privacy feature is not configured.
Privacy button is disabled
active primary line is: 700
contact IP address: 10.200.200.16 port 5060
conference admin: no
conference add mode: all
conference drop mode: never
paging-dn: config 0 [multicast] effective 0 [multicast]
Dialpeers created:
Dial-peers for Pool 2:
dial-peer voice 40001 voip
destination-pattern 700$
session target ipv4:10.200.200.16:5060
session protocol sipv2
dtmf-relay sip-kpml
codec g711ulaw bytes 160
no vad
after-hours-exempt FALSE
Statistics:
Active registrations : 1
Total SIP phones registered: 1
Total Registration Statistics
Registration requests : 1
Registration success : 1
Registration failed : 0
unRegister requests : 0
unRegister success : 0
unRegister failed : 0
Attempts to register
after last unregister : 0
Last register request time : 13:33:09.593 GMT+2 Sun Jul 13 2014
Last unregister request time :
Register success time : 13:33:09.593 GMT+2 Sun Jul 13 2014
Unregister success time :
--------------------------------------------------------------------------------------------------
ephone-dn 88 dual-line
number 701
label GSPA
description URMET Dialog
name GSPA
hold-alert 30 originator
And now? What do we have to configure to be able to hear the doorbell ringing (as f.e. a button on our ephones? But how should we do this because the number 700 (door-bell) ist not an ephone-dn - it's a dial peer.... ?
What do we have to configure on our ephones?
We don't understand if now something is missing or misconfigured.
Any help very (!) appreciated, best regards,
Georg