10-08-2010 07:44 AM - edited 03-16-2019 01:14 AM
I know it's been asked before, but I can't seem to get my phone to convert.
https://supportforums.cisco.com/message/1176500#1176500
https://supportforums.cisco.com/message/1081618#1081618
https://supportforums.cisco.com/message/1171163#1171163
Can anyone help?
Below is the list of files i have on my TFTP server. Phone is getting an IP from my DHCP and gets TFTP server's IP as an option.
I can see the phone (7960) go out and download files from TFTP, but eventually the phone would show TFTP time out.
OS79XX.TXT (has one line inside P003-08-11-00)
P0S3-08-11-00.loads
P0S3-08-11-00.sb2
P003-08-11-00.bin
P003-08-11-00.sbn
Do I need any other files?
Solved! Go to Solution.
10-18-2010 02:59 PM
Can u try this?
Using wordpad, create a file called SIPDefault.cnf with following contents.
Make sure you have correct .loads file on TFTP (here I am pointing it to
P0S3-08-11-00.loads. Put this file on your TFTP server.
# SIP Default Generic Configuration File
# Image Version
image_version: P0S3-08-11-00
Note: Make sure there is no CRLF or blank space after the filename
and there is exactly 1 space between the : and P (as shown above)
If it still fails, please upload tftp logs along with this file.
10-08-2010 09:13 AM
Most likely, you need to update to an intermediate version before.
10-08-2010 11:40 AM
Log files for CTLSEP000628954235 & CTLSEP000628956511 attached
10-08-2010 11:41 AM
10-09-2010 04:42 AM
With CME or CM, you should use SCCP, not SIP.
10-09-2010 05:20 AM
I need to convert them to SIP so they can be used with asterisk. Phones came from a CME environment, which I no longer have access to.
10-09-2010 08:49 AM
Which SCCP version do they have now ?
Try the corresponding SIP version.
10-09-2010 11:10 AM
it has 8.0 (8.0)
boot load id PC03A300
DSP 4.0(4.0)(A0)
Will try 8.0SIP
10-09-2010 11:28 AM
10-09-2010 12:20 PM
Do a keypad reset sequence.
10-09-2010 12:23 PM
did that # on power up and then 123456789*0#
10-09-2010 12:22 PM
I created XMLDefault.cnf.xml with a tag
now i am getting protocol application invalid on the phone
10-18-2010 01:28 PM
Still looking for help...
10-18-2010 02:03 PM
Saw Document ID: 67942
IP Phone 7940/7960 Fails to Boot - Protocol Application Invalid, but don't think it applies to my phones because they are running 8.0
10-18-2010 02:59 PM
Can u try this?
Using wordpad, create a file called SIPDefault.cnf with following contents.
Make sure you have correct .loads file on TFTP (here I am pointing it to
P0S3-08-11-00.loads. Put this file on your TFTP server.
# SIP Default Generic Configuration File
# Image Version
image_version: P0S3-08-11-00
Note: Make sure there is no CRLF or blank space after the filename
and there is exactly 1 space between the : and P (as shown above)
If it still fails, please upload tftp logs along with this file.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: