Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Converting from H323 to MGCP

Hi,

I am converting from H323 to MGCP. Here is my H323 gateway config:

isdn switch-type primary-ni

!

voice-card 0

no dspfarm

voice class codec 1

codec preference 1 g711ulaw

voice class h323 1

h225 timeout tcp establish 3

h225 timeout setup 3

application

global

service alternate Default

!

controller T1 0/0/0

framing esf

linecode b8zs

pri-group timeslots 1-24

!

!

!

interface GigabitEthernet0/0

description Data interface

ip address x.x.x.x 255.255.255.0

duplex auto

speed auto

!

interface GigabitEthernet0/1

description Voice interface

ip address y.y.y.y 255.255.255.0

duplex auto

speed auto

h323-gateway voip interface

h323-gateway voip bind srcaddr x.x.x.x

!

interface Serial0/0/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn incoming-voice voice

isdn outgoing display-ie

no cdp enable

!

control-plane

!

voice-port 0/0/0:23

!

!

!

dial-peer voice 10 pots

description 9911 calling

destination-pattern 9911

port 0/0/0:23

forward-digits 3

!

dial-peer voice 11 pots

description 911 calling

destination-pattern 911

port 0/0/0:23

forward-digits all

!

dial-peer voice 12 pots

description Local calling

destination-pattern 9[2-9]..[2-9]......

port 0/0/0:23

forward-digits 10

!

dial-peer voice 13 pots

description Naional CND/US calling

destination-pattern 9[0-1][2-9]..[2-9]......

port 0/0/0:23

forward-digits 11

!

dial-peer voice 14 pots

description Service calls

destination-pattern 9[2-8]11

port 0/0/0:23

forward-digits 3

!

dial-peer voice 15 pots

description International calling

destination-pattern 9011T

port 0/0/0:23

prefix 011

!

dial-peer voice 16 pots

description Operator

destination-pattern 90.T

port 0/0/0:23

forward-digits 0

prefix 0

!

dial-peer voice 990 voip

destination-pattern .

session target ipv4:x.x.x.x

dtmf-relay h245-alphanumeric

no vad

!

dial-peer voice 999 pots

incoming called-number .T

direct-inward-dial

port 0/0/0:23

!

telephony-service

srst mode auto-provision none

max-ephones 20

max-dn 40

ip source-address x.x.x.x port 2000

max-conferences 8 gain -6

transfer-system full-consult

secondary-dialtone 9

MGCP Config:

application

global

service alternate default

!

controller T1 0/2/0

framing esf

linecode b8zs

pri-group timeslots 1-24 service mgcp

interface Serial0/2/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

!

!

ccm-manager fallback-mgcp

ccm-manager mgcp

no ccm-manager fax protocol cisco

ccm-manager music-on-hold

ccm-manager config server x.x.x.x

ccm-manager config

!

mgcp

mgcp call-agent x.x.x.x 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

mgcp validate call-agent source-ipaddr

no mgcp fax t38 ecm

mgcp fax t38 inhibit

mgcp rtp payload-type g726r16 static

mgcp bind control source-interface FastEthernet0/1

mgcp bind media source-interface FastEthernet0/1

!

mgcp profile default

!

dial-peer voice 10 pots

service mgcpapp

destination-pattern 9T

incoming called-number .

direct-inward-dial

!

call-manager-fallback

secondary-dialtone 9

max-conferences 8 gain -6

transfer-system full-consult

timeouts ringing 30

ip source-address x.x.x.x port 2000

max-ephones 36

max-dn 72 dual-line

access-code pri 9 direct-inward-dial

I am looking for expert opinion about the config conversion that will work. Appreciate your help.

Thanks.

5 REPLIES
Hall of Fame Super Gold

Re: Converting from H323 to MGCP

Why do you want to do that? You loose features and flexibility.

New Member

Re: Converting from H323 to MGCP

That is my customer requirement.

New Member

Re: Converting from H323 to MGCP

What is better MGCP or H.323 ???

Hall of Fame Super Gold

Re: Converting from H323 to MGCP

Is your customer properly informed ?

I hear that sentence used too often as an excuse for poor choices.

New Member

Re: Converting from H323 to MGCP

The customer took the descision and there is no point raising question right now. I wanted to check my configuration before I implement on the system.

158
Views
0
Helpful
5
Replies