Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Corlist

Hello

Here is my corlist configuration. We need to restrcit User 'A' to Local calls only, but corlist is not working as expected. user 'A' can call local / national / international.

dial-peer cor list International

member Local

member 911

member National

member International

dial-peer voice 10 voip

corlist outgoing Local

destination-pattern 1[2-6]......

session target ipv4: 10.10.10.100

dial-peer voice 11 voip

corlist outgoing National

destination-pattern 10[4-6].......

session target ipv4: 10.10.10.100

dial-peer voice 12 voip

corlist outgoing International

destination-pattern 100[2-6].........

session target ipv4: 10.10.10.100

Voice register dn 10

number 6610

mwi

Voice register dn 11

number 6611

mwi

Voice register dn 12

number 6612

mwi

voice register pool 10

id mac 1111.1111.1111

number 1 dn 10

cor incomming Local default

username A password ????

voice register pool 11

id mac 1111.1111.1111

number 1 dn 11

cor incomming National default

username B password ????

voice register pool 12

id mac 1111.1111.1111

number 1 dn 12

cor incomming International default

username C password ????

thanks

Anthony

1 ACCEPTED SOLUTION

Accepted Solutions

Corlist

try to update the outgoing naming only

remove the above one and make it as per bellow

dial-peer cor list Local-call

member Local

dial-peer cor list National-call

member National

dial-peer cor list International-call

member International

dial-peer cor list 911-call

member 911

update the dial peers with the above names example:

dial-peer voice 10 voip

corlist outgoing Local-call

destination-pattern 1[2-6]......

session target ipv4: 10.10.10.100

for testing try to apply the incoming cor on the ephone-DN it self without using the default keyword:

Ephone-dn x

Number xxx

Cor incoming Local

for more information see the blow link:

http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml

hope this help

if helpful Rate

4 REPLIES

Re: Corlist

hi anthony

there are some steps mising see below

1- define the COR

dial-peer cor custom

member Local

member 911

member National

member International

2- outbound COR lists

dial-peer cor list International

member International

dial-peer cor list Local

member Local

dial-peer cor list National

member National

dial-peer cor list 911

member 911

3- incoming COR lists ( to be applied under the lines/devices)

dial-peer cor list CORInternational

member International

member Local

member National

member 911

dial-peer cor list CORNational

member Local

member National

member 911

dial-peer cor list CORLocal

member Local

member 911

and apply the incoming cor lists above and give it a go

hope this help

New Member

Corlist

Hi Marwanshawi

Doesn't work yet, here is updated config

dial-peer cor custom

name Local

name National

name 911

name International

dial-peer cor list Local

member Local

dial-peer cor list National

member National

dial-peer cor list International

member International

dial-peer cor list 911

member 911

dial-peer cor list  Cor-Local

member Local

member 911

dial-peer cor list  Cor-National

member Local

member 911

member National

dial-peer cor list  Cor-International

member Local

member 911

member National

member International

dial-peer voice 10 voip

corlist outgoing Local

destination-pattern 1[2-6]......

session target ipv4: 10.10.10.100

dial-peer voice 11 voip

corlist outgoing National

destination-pattern 10[4-6].......

session target ipv4: 10.10.10.100

dial-peer voice 12 voip

corlist outgoing International

destination-pattern 100[2-6].........

session target ipv4: 10.10.10.100

Voice register dn 10

number 6610

mwi

Voice register dn 11

number 6611

mwi

Voice register dn 12

number 6612

mwi

voice register pool 10

id mac 1111.1111.1111

number 1 dn 10

cor incomming Cor-Local default

username A password ????

voice register pool 11

id mac 1111.1111.1111

number 1 dn 11

cor incomming Cor-National default

username B password ????

voice register pool 12

id mac 1111.1111.1111

number 1 dn 12

cor incomming Cor-International default

username C password ????

am I applying the 'cor incomming' command in the right place.

thanks

Anthony

Corlist

try to update the outgoing naming only

remove the above one and make it as per bellow

dial-peer cor list Local-call

member Local

dial-peer cor list National-call

member National

dial-peer cor list International-call

member International

dial-peer cor list 911-call

member 911

update the dial peers with the above names example:

dial-peer voice 10 voip

corlist outgoing Local-call

destination-pattern 1[2-6]......

session target ipv4: 10.10.10.100

for testing try to apply the incoming cor on the ephone-DN it self without using the default keyword:

Ephone-dn x

Number xxx

Cor incoming Local

for more information see the blow link:

http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml

hope this help

if helpful Rate

New Member

Corlist

Thanks. It works without the default keyword

387
Views
0
Helpful
4
Replies