Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CUBE and SIP Trunk

Hi all,

This my first attempt to integrate CUBE and Telco using SIP protocol.

I have CUCM >> H323 GW >> Telco.

now I will configure the GW to work as CUBE. I asked the Telco for the parameters and I have this issue:

they gave me two IPs for SIP one for Signaling and one for Media. How I can distinguish the traffic.

6 REPLIES
Silver

Re: CUBE and SIP Trunk

Hi

What you mean they gave you two ip address? Are those ip addresses to use on your gateway or you need to point to them?

If you need to point to them, then you need to use the Signalling only. The RTP address will be negotiated during the signalling. So you do not need to configure anything for it. But if you have any firewall or ACL, make sure you permit udp traffic from the media ip.

But if those IP address to use for your gateway. Then you can use sip bind command.

voice service voip

sip

  bind {control | all} source-  interface interface-id


!

Let me know if this helps

Thanks

- abu

New Member

Re: CUBE and SIP Trunk

Hi Abu Hadee,

I got two IP address for SIP setting and one for IP address for connectivity,

What I am going to do is to configure the gig interface for P2P connectivity.

but inside the dial-peer shall I use the signaling IP address in session target command.

Do you have sample of the configuration?

Silver

Re: CUBE and SIP Trunk

Hi,

I'm still confused if you have to use all these IP address for your gateway or one for your gateway, other two for remote

lets say you've received following IP Address.

1. A.A.A.A for your GW conectivity

2. B.B.B.B for SIP Signalling

3. C.C.C.C for meida

Here is scenario 1, say you've to use one IP for your GW and other two for remote

interface gig0/0

ip address A.A.A.A 255.255.255.0 !

!

voice service voip

sip

bind all gig0/0

!

dial-peer voice 1 voip

destination-patter 9T

incoming called-number .

session-target ipv4:B.B.B.B

codec g711ulaw

no vad

!

C.C.C.C you do not need to configure anything in the voip side. As this one will be media ip and will be negotiated autometically. All if you do permit any UDP sourced from that.

Option two: If you need to configure all three in your gw

interface gig0/0

ip address A.A.A.A 255.255.255.0 !

!

interfae loopback 1

ip address B.B.B.B 255.255.255.255 !

interfae loopback 1

ip address C.C.C.C 255.255.255.255 !

voice service voip

sip

bind control loopback1

bind media lookback2

!

dial-peer voice 1 voip

destination-patter 9T

incoming  called-number .

session-target dns:

codec  g711ulaw

no vad

New Member

Re: CUBE and SIP Trunk

Thank you too much Abu Hadee,

I will test it and if I have any problemI will return to you.

New Member

Re: CUBE and SIP Trunk

I tried the configuration above, I can now place calls but I have some issues:

1- When somebody call from outside to IP phone ( one of the DID extension) the calling party always hear ringing even if I pick up the phone and answer the call. I contacted the provider regarding this and they said we are not receiving any signals that some body answer.

2- It is a DTMF issue. if I called from IP phone to out-side and AA answers the AA does not recognize the DTMF. the provider inform me that they are using in-band signaling, so shall I delete the dtmf command from the dial-peer?

New Member

Re: CUBE and SIP Trunk

Hello,

I'm not sure if you ever figured this out, but the answer is the "dtmf-relay rtp-nte" command, which encapsulates the dtmf signals within RTP. It takes an MTP resource, generally speaking.

Ryan

505
Views
10
Helpful
6
Replies