Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

CUCM 9.1 DIAL NUMBER

Hi.could you help me, please. I have a number +XXX (XX) XXXXXX and when I dial this number, I can't call. Answer to me please: if it is possible this setting and if it is possible, where I can find it: in CUBE or CUCM??? PLEAS!!!!!!!

14 REPLIES
Cisco Employee

Re: CUCM 9.1 DIAL NUMBER

Inbound???
Outbound call??
Call flow??

Sent from Cisco Technical Support iPad App

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: CUCM 9.1 DIAL NUMBER

outbound call

Cisco Employee

Re: CUCM 9.1 DIAL NUMBER

If you don't provide enough details and the exact behavior you're seeing, theres no way you'll get an answer.

Sent from Cisco Technical Support iPad App

HTH

java

if this helps, please rate

www.cisco.com/go/pdi

Re: CUCM 9.1 DIAL NUMBER

Hi.
Please give a look to this doc.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/9_1_1/ccmsys/CUCM_BK_C5565591_00_cucm-system-guide-91_chapter_010000.html#CUCM_RF_UAD8BE59_00


HTH

Regards

Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"
New Member

Re: CUCM 9.1 DIAL NUMBER

I set on route pattern \+!# and at \+.0!# but is doesn't work.

Re: CUCM 9.1 DIAL NUMBER

Hi.
You can try
\+.!
discard digits pre dot
prefix outgoing 00

HTH
Regards
Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"
New Member

Re: CUCM 9.1 DIAL NUMBER

Hi,

thanks for answer, but it do not work. "your call cannot be completed as dialed please consult your directory ..."

Re: CUCM 9.1 DIAL NUMBER

Hi.

What signaling protocol have you configure to reach your voice gateway? (MGCP/H323/SIP)

Check also the partition you have configured the suggested Route Pattern.

Let me know

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
New Member

Re: CUCM 9.1 DIAL NUMBER

voice gateway SIP;

CUCM 9.1 DIAL NUMBER

Hi.

Can please post a show run of your VG and a debug voice dialpeer inout during a call to an E.164 number?

Thanks

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
New Member

CUCM 9.1 DIAL NUMBER

no i don't

CUCM 9.1 DIAL NUMBER

In this case we can't help you.

Regards

Carlo

Please rate all helpful posts

"The more you help the more you learn"

Please rate all helpful posts "The more you help the more you learn"
New Member

CUCM 9.1 DIAL NUMBER

thanks for help

New Member

CUCM 9.1 DIAL NUMBER

It appears you are requiring the # character at the end of the phone  number, and also sending that to the telco. (I cannot see the entire  route pattern or translation pattern in your post.)

Try sending the number without the #

D

366
Views
6
Helpful
14
Replies