Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

CUCME Version 7.0(1) GUI Problem

Hi, I can't access to CUCME by GUI. When I put the username and the pass, then, the web page get to blank.

The commands web admin system name admin password cisco and ip http server are run.

Regards

1 ACCEPTED SOLUTION

Accepted Solutions

Re: CUCME Version 7.0(1) GUI Problem

Hello,

Please verify that you have the following files on your flash:

Admin-user.html

Admin_user.js

CiscoLogo.gif

delete.gif

dom.js

downarrow.gif

ephone_admin.html

logohome.gif

normal_user.html

normal_user.js

Plus.gif

sxiconad.gif

Tab.gif

Telephony_service.html

uparrow.gif

xml.template

xml-test.html

These are all of the files necessary to enable full GUI functionality.

Hope that helped, if so please rate.

9 REPLIES

Re: CUCME Version 7.0(1) GUI Problem

Hello,

Do you have "ip http path flash:" configured?

New Member

Re: CUCME Version 7.0(1) GUI Problem

Dear Kenneth...Yes

Bronze

Re: CUCME Version 7.0(1) GUI Problem

Hi to access the GUI and allow the admin to add remove DNs from web interface:

ip http server

ip http path flash:

telephony-service

web admin system name admin password cisco

dn-webedit

time-webedit

Hope this help

David

New Member

Re: CUCME Version 7.0(1) GUI Problem

Cool, I'm going to re-configure and I will show you the result.

New Member

Re: CUCME Version 7.0(1) GUI Problem

Hi..fail. :(. I think that upgrading will be fine.

New Member

Re: CUCME Version 7.0(1) GUI Problem

Hi David

I upgraded to 124-22.T (Cisco 2811), but i still can't access to GUI. I put the user and passw and then it show me the page in blank. Pls.,see the command

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip http path flash:

telephony-service

em logout 0:0 0:0 0:0

max-ephones 42

max-dn 80

ip source-address 10.175.206.1 port 2000

system message CME

user-locale ES

network-locale ES

time-zone 18

time-format 24

date-format dd-mm-yy

voicemail 3120

max-conferences 8 gain -6

web admin system name admin password cisco

dn-webedit

time-webedit

transfer-system full-consult

create cnf-files version-stamp 7960 Mar 31 2009 15:20:31

I don't know what happens

Re: CUCME Version 7.0(1) GUI Problem

Hello,

Please verify that you have the following files on your flash:

Admin-user.html

Admin_user.js

CiscoLogo.gif

delete.gif

dom.js

downarrow.gif

ephone_admin.html

logohome.gif

normal_user.html

normal_user.js

Plus.gif

sxiconad.gif

Tab.gif

Telephony_service.html

uparrow.gif

xml.template

xml-test.html

These are all of the files necessary to enable full GUI functionality.

Hope that helped, if so please rate.

New Member

Re: CUCME Version 7.0(1) GUI Problem

Dear Kenneth, the problem is solved.

Thanks a lot!!

New Member

Re: CUCME Version 7.0(1) GUI Problem

Hi All,

i have CME version 7.1 with IOS 12.4(24T1)and i experienced the same problem with the GUI interface. i found that the problem came from copying the GUI files using a flash reader, when i uploaded the files using the archive command and used the command ip http server path flash: ,the GUI worked fine but after a restart.

296
Views
0
Helpful
9
Replies
CreatePlease to create content