Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

dial peer configuration (auto stripping)

HI,

I am facing issue with my h.323 gateway. I am trying to call a number 01147771171 from my ip phone. and it is not going through. When i checked on the gaetway it is showing the called party number as 47771171, it is triping 011 from the pattern.

Please find below the dial peeer config

dial-peer voice 16 pots

destination-pattern 0[1-6].........$

port 0/0/0:15

forward-digits all

and the output from debug isdn q931

NDArouter_01#

Jul 16 08:42:07.144: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 08:42:07.144: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 08:42:07.144: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x02F3 callID = 0x8276 switch = primary-4ess interface = User

Jul 16 08:42:07.144: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x02F3

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x2181, '1001'

                Plan:ISDN, Type:National

        Called Party Number i = 0x91, '47771171'

                Plan:ISDN, Type:International

Jul 16 08:42:07.164: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x82F3

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

Please help me on this.

Regards,

Pawan Arora

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
VIP Super Bronze

dial peer configuration (auto stripping)

Ok, your provider still doesnt like that..can you try unknown..

Int s0/0/0:15

isdn map address ^011* plan unknown type unknown

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
17 REPLIES
Community Member

Re: dial peer configuration (auto stripping)

hi,

use: no digit-strip

regards

Community Member

dial peer configuration (auto stripping)

i have applied that command also but got the same

dial-peer voice 16 pots

destination-pattern 0[1-6].........$

no digit-strip

port 0/0/0:15

forward-digits all

here is the output

Jul 16 08:57:17.059: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 08:57:17.059: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 08:57:17.059: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x031A callID = 0x829F switch = primary-4ess interface = User

Jul 16 08:57:17.059: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x031A

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839C

                Exclusive, Channel 28

        Calling Party Number i = 0x2181, '1001'

                Plan:ISDN, Type:National

        Called Party Number i = 0x91, '47771171'

                Plan:ISDN, Type:International

Jul 16 08:57:17.083: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x831A

        Channel ID i = 0xA9839C

                Exclusive, Channel 28

Jul 16 2012 14:27:18: %ISDN-6-DISCONNECT: Interface Serial0/0/0:30  disconnected from 9818849802 , call lasted 43 seconds

Jul 16 08:57:18.331: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x0316

        Cause i = 0x8090 - Normal call clearing

Jul 16 08:57:18.379: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x8316

Jul 16 08:57:18.383: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0316

Jul 16 2012 14:27:20: %ISDN-6-DISCONNECT: Interface Serial0/0/0:29  disconnected from 8130680797 , call lasted 28 seconds

Jul 16 08:57:20.927: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x0318

        Cause i = 0x8090 - Normal call clearing

Jul 16 08:57:20.979: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x8318

Jul 16 08:57:20.983: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x0318

Jul 16 08:57:22.283: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x031A

        Cause i = 0x8090 - Normal call clearing

Jul 16 08:57:22.331: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x831A

Jul 16 08:57:22.335: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x031Au all

All possible debugging has been turned off

NDArouter_01#term no mon

Community Member

dial peer configuration (auto stripping)

HI,

I have made some changes and it takes the 011 but my calls are not going through

dial-peer voice 16 pots

destination-pattern 0[1-6].........$

no digit-strip

port 0/0/0:15

forward-digits all

prefix 011

ISDN 931 debug:

Jul 16 09:05:29.971: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 09:05:29.971: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 09:05:29.971: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x0336 callID = 0x82BC switch = primary-4ess interface = User

Jul 16 09:05:29.971: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x0336

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x2181, '1001'

                Plan:ISDN, Type:National

        Called Party Number i = 0x91, '01147771112'

                Plan:ISDN, Type:International

Jul 16 09:05:29.995: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x8336

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

Jul 16 09:05:36.211: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x8336

        Cause i = 0x8483 - No route to destination

        Progress Ind i = 0x8288 - In-band info or appropriate now available

Jul 16 09:05:36.215: ISDN Se0/0/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x82BC

Jul 16 09:05:42.455: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x0336

Jul 16 09:05:42.467: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x8336u all

Re: dial peer configuration (auto stripping)

Hi, from the logs it showing that your teleco is unable to route the call, i.e the number is unroutable.

Make sure that you are sending the right number (LD, National, or international). Else, you may check this with your teleco.

Sent from Cisco Technical Support iPhone App

Community Member

dial peer configuration (auto stripping)

But earlier it was working fine..

Blue

dial peer configuration (auto stripping)

HI

I believe your CUCM is changing National call to International call. Your service provider is expecting that

Plan:ISDN, Type:National and not international.

Check your CUCM and  convert it in National. May be your service provider added this criteria newly.

Regards

Ronak Patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
Community Member

dial peer configuration (auto stripping)

Hi Ronak,

How can i check on the call manager? is there any pareameter for this

Blue

Re: dial peer configuration (auto stripping)

HI

In your route pattern , select as below. Change Type to National . 

Regards

Ronak Patel

rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.
VIP Super Bronze

Re: dial peer configuration (auto stripping)

Pawan is this an international call? Your provider is saying they ant route the call

Calling Party Number i = 0x2181, '1001'

                Plan:ISDN, Type:National

        Called Party Number i = 0x91, '01147771112'

                Plan:ISDN, Type:International

Jul 16 09:05:36.211: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x8336

        Cause i = 0x8483 - No route to destination

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
Community Member

dial peer configuration (auto stripping)

no this is national dialing number

VIP Super Bronze

dial peer configuration (auto stripping)

Then your isdn plan type is wrong. It is showing as international. You need to change it to either national or unknown.

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
VIP Super Bronze

dial peer configuration (auto stripping)


Configure this on your gateway:

Int s0/0/0:15

isdn map address ^011* plan ISDN type National

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
Community Member

dial peer configuration (auto stripping)

I have changed it to national and still call is not going through...in the debug it is showing national

VIP Super Bronze

dial peer configuration (auto stripping)

Please send "debug isdn q931" only.

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
Community Member

dial peer configuration (auto stripping)

Here it is

Jul 16 10:14:45.692: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x0 may be overriden; sw-type 2

Jul 16 10:14:45.692: ISDN Se0/0/0:15 Q931: pak_private_number: Invalid type/plan 0x0 0x8 may be overriden; sw-type 2

Jul 16 10:14:45.692: ISDN Se0/0/0:15 Q931: Sending SETUP  callref = 0x03B9 callID = 0x8341 switch = primary-4ess interface = User

Jul 16 10:14:45.692: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x03B9

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x2181, '1001'

                Plan:ISDN, Type:National

        Called Party Number i = 0xA1, '01147771112'

                Plan:ISDN, Type:National

Jul 16 10:14:45.716: ISDN Se0/0/0:15 Q931: RX <- SETUP_ACK pd = 8  callref = 0x83B9

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

Jul 16 10:14:57.764: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0x83B9

Jul 16 10:15:04.252: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0x83B9

        Cause i = 0x849C - Invalid number format (incomplete number)

        Progress Ind i = 0x8288 - In-band info or appropriate now available

Jul 16 10:15:04.252: ISDN Se0/0/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0x8341

Jul 16 10:15:08.308: ISDN Se0/0/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x03B9

Jul 16 10:15:08.320: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x83B9u all

All possible debugging has been turned off

VIP Super Bronze

dial peer configuration (auto stripping)

Ok, your provider still doesnt like that..can you try unknown..

Int s0/0/0:15

isdn map address ^011* plan unknown type unknown

Please rate all useful posts

"'Nature is too thin a screen, the glory of the omnipresent God bursts through it everywhere"-Ralph Waldo Emerson

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
Community Member

dial peer configuration (auto stripping)

its working now, thanks for your support.

1097
Views
0
Helpful
17
Replies
CreatePlease to create content