Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Dial peer for variable length numbers in Germany and Interdigit Timeout (CME)

Hi,

I'm using CME 8.6 with a VIC2-2BRI on an ISDN BRI line. Because of the variable length numbers in Germany a use .T as my destination pattern in the ISDN dial peer. If a dial a number, it takes 10 seconds before the call gets placed. If I dial # at the end of the number, the calls gets placed immediately. I understand that this behaviour is controlled by the interdigit timer? I set it to 2 seconds under my voice port, but it still takes 10 seconds for the router to dial.

interface BRI0/0/0

description CONNECTION_TO_NTBA

no ip address

isdn switch-type basic-net3

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice

voice-port 0/0/0

translation-profile incoming ADD_LEADING_ZERO_INCOMING_ISDN

compand-type a-law

no comfort-noise

cptone DE

timeouts interdigit 2

description ISDN_SPEECH

bearer-cap Speech

dial-peer voice 10 pots

description INCOMING_AND_OUTGOING_ISDN_CALLS

translation-profile incoming INCOMING_ISDN_CALLS

translation-profile outgoing OUTGOING_ISDN_CALLS

incoming called-number 800XX[YZ]

destination-pattern .T

no digit-strip

port 0/0/0

no sip-register

1 ACCEPTED SOLUTION

Accepted Solutions

Re: Dial peer for variable length numbers in Germany and Interdi

then set the timer manually. Uner Telephony-service

timeouts interdigit x (value in seconds)

Please rate helpful answers!

6 REPLIES

Dial peer for variable length numbers in Germany and Interdigit

Do you have any timer set under telephony-service? Please post your running-config here.

New Member

Re: Dial peer for variable length numbers in Germany and Interdi

No, I don't. I uploaded my running-config.

Re: Dial peer for variable length numbers in Germany and Interdi

then set the timer manually. Uner Telephony-service

timeouts interdigit x (value in seconds)

Please rate helpful answers!

New Member

Re: Dial peer for variable length numbers in Germany and Interdi

Thanks, I guess I just set the timer in the wrong place.
Now I set it under 'telephone-service' for SCCP and under 'voice-register-global' for SIP. Works as expected.

Re: Dial peer for variable length numbers in Germany and Interdi

Hi.
Can you please collect debug vpm all and debug isdn q931 while dialing out without pressing #

Thanks

Carlo

Sent from Cisco Technical Support iPhone App

Please rate all helpful posts "The more you help the more you learn"
New Member

Re: Dial peer for variable length numbers in Germany and Interdi

Of course:

000451: Nov 13 2013 21:06:14.277 CET: ISDN BR0/0/0 Q931: RX <- FACILITY pd = 8  callref = N/A

    Facility i = 0x91A10F02024275060604008267010A020101

        Protocol Profile = Remote Operations Protocol

        0xA10F02024275060604008267010A020101

        Component = Invoke component

             3PTY Request

    Called Party Number i = 0xA1, '2774XXXXXX'

        Plan:ISDN, Type:National

000452: Nov 13 2013 21:06:15.517 CET: ISDN BR0/0/0 Q931: Applying typeplan for sw-type 0x1 is 0x0 0x0, Calling num 02774XXXXXX

000453: Nov 13 2013 21:06:15.517 CET: ISDN BR0/0/0 Q931: Sending SETUP  callref = 0x0018 callID = 0x801E switch = basic-net3 interface = User

000454: Nov 13 2013 21:06:15.521 CET: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8  callref = 0x18

    Bearer Capability i = 0x8090A3

        Standard = CCITT

        Transfer Capability = Speech 

        Transfer Mode = Circuit

        Transfer Rate = 64 kbit/s

    Channel ID i = 0x81

        Preferred, B1

    Calling Party Number i = 0x0080, '02774XXXXXX'

        Plan:Unknown, Type:Unknown

    Called Party Number i = 0x80, '02774XXXXXX'

        Plan:Unknown, Type:Unknown

000455: Nov 13 2013 21:06:15.761 CET: ISDN BR0/0/0 Q931: RX <- SETUP_ACK pd = 8  callref = 0x98

    Channel ID i = 0x89

        Exclusive, B1

000456: Nov 13 2013 21:06:16.093 CET: ISDN BR0/0/0 Q931: RX <- ALERTING pd = 8  callref = 0x98

    Facility i = 0x91A10F0202447F0606040082670101020101

        Protocol Profile = Remote Operations Protocol

        0xA10F0202447F0606040082670101020101

        Component = Invoke component

             3PTY Request

    Progress Ind i = 0x8288 - In-band info or appropriate now available 

    Display i = 'CCNR moeglich'

000457: Nov 13 2013 21:06:16.101 CET: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec

000458: Nov 13 2013 21:06:16.105 CET: flex_dsprm_forking_mixing_support:

000459: Nov 13 2013 21:06:16.109 CET: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec

000460: Nov 13 2013 21:06:22.412 CET: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd = 8  callref = 0x18

    Cause i = 0x8090 - Normal call clearing

000461: Nov 13 2013 21:06:22.492 CET: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x01

    Cause i = 0x8090 - Normal call clearing

000462: Nov 13 2013 21:06:22.516 CET: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x98

000463: Nov 13 2013 21:06:22.520 CET: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x18

000464: Nov 13 2013 21:06:22.524 CET: flex_dsprm_close_cleanup

506
Views
0
Helpful
6
Replies
CreatePlease to create content