Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

dial-peer pots incoming redirect

there is a command that is equivalet to the connection PLAR of the voice port, for the dial-peer pots ??.

my problem is that i want to connect an ephone with a specific called isdn number.

the isdn bri haven't DID.

18 REPLIES
Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Hi, the simpler way is to add the called number as "secondary" under ephone-dn.

This assume you're using CME, if not, please clarify.

New Member

Re: dial-peer pots incoming redirect

yes is a CME,

ok i use a dial-peer that not use a incoming called-number but destination-pattern ?

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

You don't need any DP. Either configure secondary number for DN as suggested above, or translate the called number to an extension number, via voice translation-profile and translation-rule.

As an appreciation to those providing answers, please rate useful posts with the scrollbox below!

New Member

Re: dial-peer pots incoming redirect

the conf not work the isdn not go to up

see the debug

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Have you associated the ephone-dn to an ephone via button command ?

Note, generally you want to use dual-line ephone-dn, else you won't be able to do consultive transfer, call-waiting, etc.

New Member

Re: dial-peer pots incoming redirect

yes i have to change the dn with dual-line but the result it's the same

ephone 18

mac-address 001B.5452.FC51

type 7911

button 1:31

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Please send output of "show ephone 001B.5452.FC51" and if it is REGISTERED send output of "debug isdn q931". No other debugs are to be enabled.

New Member

Re: dial-peer pots incoming redirect

see the attachment

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Please send output of "show diag". You might be using a WIC BRI card for data, or not have the necessary PVDM2 card. See:

Jun 9 16:51:21 UTC: ISDN BR3/1 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x9C

Cause i = 0x80AF - Resource unavailable, unspecified

New Member

Re: dial-peer pots incoming redirect

see the attachment :)

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Hi, you have 1 of:

PVDM-256K-4=

That is enough for 4 calls, meaning 2 x ISDN BRI, but you have four ports of this kind currently installed.

Then you have:

1 x PVDM-12=

But that is the wrong type for a 1760, and is not supported, see:

http://www.cisco.com/en/US/products/hw/routers/ps221/products_tech_note09186a00800c3399.shtml

So:

- Remove PVDM-12 in internal slot 1

- Remove VIC-2BRI in either slot 2 or slot 3.

And you should be able to call. To use the additional BRI ports, you need to obtain another PVDM-256K-xx

Hope this helps, please rate post if it does!

New Member

Re: dial-peer pots incoming redirect

ok,

but if i use bri 2/1 with primary number and then i use dn with the primary number, the bri go to up but not to go with the dn and ephone.

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

Sorry, I don't understand that. What I can tell you is that the error message is due to insufficient PVDM resources.

New Member

Re: dial-peer pots incoming redirect

well see the attachment

(out call with this PVDM are all ok and are ok if I use bri associated with ivr)

New Member

Re: dial-peer pots incoming redirect

well see the attachment

(out call with this PVDM are all ok and are ok if I use bri associated with ivr)

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

I saw the attachment. The point is that you have enough PVDM resources for (possibly) 2 x BRI, but certainly not for 4.

As mentioned above, you should replace the incompatible PVDM-2 with a PVDM-256k-xx to have all the BRI ports working.

New Member

Re: dial-peer pots incoming redirect

ok tnx

i will check this conf in a new router 2800 series :)

(grazie.. almeno questo in italiano :) )

Hall of Fame Super Gold

Re: dial-peer pots incoming redirect

A PVDM2-256K-xx will be enough. I have 1760 working beautifully with CME and 12.4(4)XC

Problem is that the VIC-2BRI you have is not compatible with the ISR router so you can't reuse them.

Grazie per l'apprezzamento e saluti alla bella Sardegna.

622
Views
5
Helpful
18
Replies