cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
289
Views
0
Helpful
1
Replies

Dial Peer Question

Rod.Blackie
Level 1
Level 1

Hi Netpros.

I have two faxes in the same office which are connected to different ATA boxes. The faxes have 4 digit extensiton numbers fax 1 = 5286 fax 2= 5288

I have a H.323 gateway with the following dial peer config and translation pattern

dial-peer voice 9 pots
tone ringback alert-no-PI
description *** Outgoign POTS PEER ***
destination-pattern 9T
progress_ind setup enable 3
progress_ind progress enable 8
port 0/0/0:15
!
dial-peer voice 1 pots
description *** Incoming POTS peer ***
incoming called-number .
direct-inward-dial
port 0/0/0:15
!
dial-peer voice 5201 voip
preference 1
destination-pattern 52..
voice-class codec 1
voice-class h323 1
session target ipv4:10.118.2.10
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
ip qos dscp cs3 signaling
no vad
!
dial-peer voice 5202 voip
preference 2
destination-pattern 52..
voice-class codec 1
voice-class h323 1
session target ipv4:10.118.8.10
dtmf-relay h245-alphanumeric
ip qos dscp cs5 media
ip qos dscp cs3 signaling
no vad

voice-port 0/0/0:15
translate calling 10
translate called 1
cptone GB
!

translation-rule 10
Rule 0 ^. 90
!
!
translation-rule 1
Rule 0 755... 5

Now the problem is this - when I send a fax directly from 5286 to 5288 it works (please note I only use the 4 digit extension to dial) however when I try and dial the full national number 01**5 755888 it doesn't get accepted into the fax memory. The fax rings but nothing happens

below is an output of debug isdn q931 - can anyone help? thanks.

wifvoip#
May  6 07:31:12.314: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref = 0xA793
wifvoip#
May  6 07:31:19.510: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8  callref = 0xA793
May  6 07:31:19.514: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x2793
wifvoip#
May  6 07:31:44.811: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 5286
May  6 07:31:44.811: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num 01xx5755288
May  6 07:31:44.811: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8  callref = 0x2794
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98385
                Exclusive, Channel 5
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Calling Party Number i = 0x0081, '5286'
                Plan:Unknown, Type:Unknown
        Called Party Number i = 0x80, '01xx5755288'
                Plan:Unknown, Type:Unknown
May  6 07:31:45.007: ISDN Se0/0/0:15 Q931: RX <- CALL_PROC pd = 8  callref = 0xA794
        Channel ID i = 0xA98385
                Exclusive, Channel 5
May  6 07:31:45.091: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8  callref = 0x0002
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98382
                Exclusive, Channel 2
        Progress Ind i = 0x8583 - Origination address is non-ISDN
wifvoip#
        Calling Party Number i = 0x2181, '1xx5755286'
                Plan:ISDN, Type:National
        Called Party Number i = 0x81, '755288'
                Plan:ISDN, Type:Unknown
May  6 07:31:45.103: ISDN Se0/0/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0x8002
        Channel ID i = 0xA98382
                Exclusive, Channel 2
May  6 07:31:45.279: ISDN Se0/0/0:15 Q931: TX -> ALERTING pd = 8  callref = 0x8002
May  6 07:31:45.391: ISDN Se0/0/0:15 Q931: RX <- ALERTING pd = 8  callref = 0xA794
wifvoip#
May  6 07:31:48.043: ISDN Se0/0/0:15 Q931: TX -> CONNECT pd = 8  callref = 0x8002
May  6 07:31:48.107: ISDN Se0/0/0:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x0002
May  6 07:31:48.155: ISDN Se0/0/0:15 Q931: RX <- CONNECT pd = 8  callref = 0xA794
May  6 07:31:48.155: ISDN Se0/0/0:15 Q931: TX -> CONNECT_ACK pd = 8  callref = 0x2794
wifvoip#
May  6 07:32:19.080: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x2793
        Cause i = 0x8090 - Normal call clearing
May  6 07:32:19.240: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0xA793
May  6 07:32:19.240: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x2793
wifvoip#
May  6 07:32:28.216: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x8002
        Cause i = 0x8090 - Normal call clearing
May  6 07:32:28.376: ISDN Se0/0/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x0002
May  6 07:32:28.380: ISDN Se0/0/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x8002
May  6 07:32:28.400: ISDN Se0/0/0:15 Q931: RX <- DISCONNECT pd = 8  callref = 0xA794
        Cause i = 0x8090 - Normal call clearing
        Progress Ind i = 0x8288 - In-band info or appropriate now available
May  6 07:32:28.404: ISDN Se0/0/0:15 Q931: call_disc: PI received in disconnect; Postpone sending RELEASE for callid 0xA715

1 Reply 1

Hi Rod,

Please, tell us your enviroment configuration:

Are you using Call Manager?

Which router model? IOS?

Thank you

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: