Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Dial Peers Doubt

Hi

My customer have a configuration down. Why the numbers are match on dial-peer 1?

88132734050

82145963269

89256789541

And why the number are match on dial-peer 2?

40822000

35616978

64589696

I think that all the numbers are match in dial-peer 1 because it`s much specific, or because the voice translation, there is a change in choose of dial-peer

voice translation-rule 1

rule 1 /811/ //

rule 2 /800/ //

rule 3 /^812/ /02112/

rule 4 /^813/ /02113/

rule 5 /^814/ /02114/

rule 6 /^815/ /02115/

rule 7 /^816/ /02116/

rule 8 /^817/ /02117/

rule 9 /^818/ /02118/

rule 10 /^819/ /02119/

voice translation-profile local

translation-called 1

e1 0/0/0

trunkgroup 1

e1 0/0/1

trukgroup 1

dial-peer voice 1 pots

trunkgroup 1

destionation-pattern 8[2-9]T

direct-inward-dial

prefix 021

dial-peer voice 2 pots

trunkgroup 1

destination-pattern 8T

direct-inward-dial

4 REPLIES

Re: Dial Peers Doubt

Hello,

I believe dial-peers match dialed digits based on longest match..therefore for your first set of numbers, they match dial-peer 1 because the destination pattern 8[2-9]T matchs the first digit "8", and the second digit, which can be any number between 2 and 9, and then the "T", which can be any amount of digits to follow after that. So yes, you are correct in dial-peer 1 is a more specific match for the dialed numbers than dial peer 2.

New Member

Re: Dial Peers Doubt

Yes the 8 is secondary dialtone. So the numbers:

88132734050

82145963269

89256789541

Choosen the dial-peer 1 based on longest? There are any documentation about it? I thinked this numbers choose the dial-peer 2; more specific! The voice translation rule can change the choose of dial-peer?

Cisco Employee

Re: Dial Peers Doubt

you can issue this command:

show dialplan number

http://www.cisco.com/en/US/docs/ios/12_3/vvf_r/vrg_sh2_ps1839_TSD_Products_Command_Reference_Chapter.html#wp999333

dial-peer hunt command can be used to modify the way the numbers are matched against dial-peers

Dial Peer Configuration on Voice Gateway Routers

http://www.cisco.com/en/US/partner/docs/ios/12_3/vvf_c/dial_peer/dpeer_c.html

HTH

javalenc

if this helps, please rate

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
VIP Super Bronze

Re: Dial Peers Doubt

your config is missing the translation profile in the dila-p used for outgoing calls.

There are 3 steps to configure voice translation rule...

1. create the voice xlation rule

2. Configure the xlation profile

3. Apply the translation profile to a dail-p and choose the directiont o whihc it should be applied..

hence your config should look like this..

voice translation-rule 1

rule 1 /811/ //

rule 2 /800/ //

rule 3 /^812/ /02112/

rule 4 /^813/ /02113/

rule 5 /^814/ /02114/

rule 6 /^815/ /02115/

rule 7 /^816/ /02116/

rule 8 /^817/ /02117/

rule 9 /^818/ /02118/

rule 10 /^819/ /02119/

voice translation-profile local

translation-called 1

dial-peer voice 1 pots

trunkgroup 1

destionation-pattern 8[2-9]T

direct-inward-dial

traslation-profile outgoing local

prefix 021

dial-peer voice 2 pots

trunkgroup 1

destination-pattern 8T

direct-inward-dial

translation-profile outgoing local

Hence the translation-profile outgoing local

is missing in your config...

In essence no translation is ben used on your config right now, make the changes and see if it gives you what you want

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
106
Views
0
Helpful
4
Replies
CreatePlease login to create content