11-01-2007 06:08 PM - edited 03-15-2019 07:02 AM
Hi Guys,
What is the best practice for DID on a CCME?
I have 3 banks of DID numbers
587-3616 to 3620
587-3629 to 3633
718-5678 to 5682
CO is sending 7 digits, and customer site has 3 digits extension
I was thinking of thisâ¦
voice translation-rule 1
rule 1 /5873616 / /616/
.
.
rule 5 /5873620/ /620/
rule 6 /5873629/ /629/
.
.
rule 10 /5873633/ /633/
rule 11 /7185678/ /678/
.
.
rule 15 /7185682/ /682/
Please recommend any better suggestions? Any help would be greatly appreciated!
Solved! Go to Solution.
11-01-2007 10:38 PM
Are you planing to do a translation rule per ephone-dn?
You can prob. combine them all to two rules, since calls which are not in your did ranges should not be routed to you from the pstn.
Rules can be:
rule 1 /58736/ /6/
rule 2 /71856/ /6/
Also, outbound translation has to be configured, for the calling number.
HTH, Avner.
11-02-2007 08:47 PM
r u planing to use cue? analog phones?
dialplan-pattern is only applied to ephone-dn's, which might cause issues when you have the above mentioned devices.
regards, Avner.
11-03-2007 07:04 AM
No analog phones or CUE. I think you will find that is easy to reproduce the problem, but I didn't bothered to raise a a case with TAC, because I'm happier using translation-profile anyway.
11-01-2007 10:38 PM
Are you planing to do a translation rule per ephone-dn?
You can prob. combine them all to two rules, since calls which are not in your did ranges should not be routed to you from the pstn.
Rules can be:
rule 1 /58736/ /6/
rule 2 /71856/ /6/
Also, outbound translation has to be configured, for the calling number.
HTH, Avner.
11-02-2007 04:01 PM
What I did was, under telephony-service
dialplan-pattern 1 5873... extension-length 3
dialplan-pattern 3 7185... extension-length 3
And it seems good. I am not sure if this is a good practice.
11-02-2007 04:21 PM
Good practice and even better if it works for you. Last time I tried, the second dialplan-patter did not worked. I have to say, it was a different situations, two same DID ranges and and two E1 PRI circuits.
11-02-2007 08:47 PM
r u planing to use cue? analog phones?
dialplan-pattern is only applied to ephone-dn's, which might cause issues when you have the above mentioned devices.
regards, Avner.
11-03-2007 07:04 AM
No analog phones or CUE. I think you will find that is easy to reproduce the problem, but I didn't bothered to raise a a case with TAC, because I'm happier using translation-profile anyway.
11-03-2007 09:54 AM
It's a 1 - T1 PRI circuit line, and only for ephone-dn's.
I am using cue, and VM seems to function fine, along with the AA, and transfer to VM.
However I do have 1 DID that is for the Fax. What I did was created...
voice-port 0/1/0
description FXS
dial-peer voice 502 pots
destination-pattern 5873620
port 0/1/1
So far I have tested, and the PRI does ring the FXS port, along with the proper DID's with the correct extention and phone.
I have been reading the translation profile and it seems slick. I might have to tried that too.
11-03-2007 10:05 AM
Hi,
when connecting fax, I'm usually happy doing like you did (no pun intended :), that is leaving the full number as destination-pattern.
This because is seldom necessary to assign to fax a real extension to be called from within the office.
Thanks for the nice rating and good luck!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: