cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
471
Views
0
Helpful
5
Replies

Directing 1 PSTN to a specific extension and use for incoming and outgoing

edwincharles
Level 1
Level 1

Hi,

any one can help configure a specific pstn line to a specific extension

call manager 6 with voice gateways

voice gateways as 12 pstn lines,

but i need a specific line to be direct to a specific extension so the user can exclusivily use it for him only for making outgoing and incoming

5 Replies 5

paolo bevilacqua
Hall of Fame
Hall of Fame

This is done with CSS/Partitions and associating gateway resources.

Are you familiar/certified for CUCM configuratio? If not it would be better have someone that is, to do it.

What type of lines?

Are you using MGCP, SIP or H323 to control the GW?

Chris

Lines are FXO PSTN

H323

Then configure the voice-ports with PLAR configuration pointing to the actual extension and ensure it matches a voip dial-peer that points to CUCM, i.e.

voice-port 3/0

connection plar opx 2000

caller-id enable

dial-peer voice 1 voip

session target ipv4:

destination-pattern 2..

dtmf-relay h245-signal

codec g711ulaw

no vad

!

HTH,

Chris

hi chris,

will it work for outgoing call through specific port if the extension for the user is 2241 and fxo port is 0/0/1, and outgoing should work only for the user 2241 only

!

voice translation-rule 9

rule 1 /\(5.......\)/ /90\1/

rule 2 /^1\(......\)/ /9\1/

rule 3 /\(3.......\)/ /90\1/

rule 4 /\(4.......\)/ /90\1/

rule 6 /\(6.......\)/ /90\1/

rule 7 /\(7.......\)/ /90\1/

rule 8 /\(2.......\)/ /90\1/

!

!

voice translation-profile incoming_add_9

translate calling 9

voice-port 0/0/0

translation-profile incoming incoming_add_9

supervisory disconnect dualtone mid-call

supervisory custom-cptone SA-custom

no battery-reversal

cptone BR

timeouts call-disconnect 2

timeouts wait-release 2

connection plar opx 5555

caller-id enable

caller-id alerting line-reversal

caller-id alerting dsp-pre-allocate

!

voice-port 0/0/1

supervisory disconnect dualtone mid-call

supervisory custom-cptone SA-custom

no battery-reversal

cptone BR

timeouts call-disconnect 2

timeouts wait-release 2

connection plar opx 5555

caller-id enable

caller-id alerting line-reversal

caller-id alerting dsp-pre-allocate

!

dial-peer voice 1000 voip

preference 1

destination-pattern 1...

session target ipv4:10.22.22.241

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 1001 voip

preference 2

destination-pattern 1...

session target ipv4:10.22.22.240

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 100 pots

destination-pattern 9T

port 0/0/0

!

dial-peer voice 101 pots

destination-pattern 9T

port 0/0/1

!

!

voice translation-rule 9

rule 1 /\(5.......\)/ /90\1/

rule 2 /^1\(......\)/ /9\1/

rule 3 /\(3.......\)/ /90\1/

rule 4 /\(4.......\)/ /90\1/

rule 6 /\(6.......\)/ /90\1/

rule 7 /\(7.......\)/ /90\1/

rule 8 /\(2.......\)/ /90\1/

!

!

voice translation-profile incoming_add_9

translate calling 9

voice-port 0/0/0
translation-profile incoming incoming_add_9
supervisory disconnect dualtone mid-call
supervisory custom-cptone SA-custom
no battery-reversal
cptone BR
timeouts call-disconnect 2
timeouts wait-release 2
connection plar opx 5555
caller-id enable
caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate
!
voice-port 0/0/1
supervisory disconnect dualtone mid-call
supervisory custom-cptone SA-custom
no battery-reversal
cptone BR
timeouts call-disconnect 2
timeouts wait-release 2
connection plar opx 5555
caller-id enable
caller-id alerting line-reversal
caller-id alerting dsp-pre-allocate
!

dial-peer voice 1000 voip
preference 1
destination-pattern 1...
session target ipv4:10.22.22.241
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 1001 voip
preference 2
destination-pattern 1...
session target ipv4:10.22.22.240
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 100 pots
destination-pattern 9T
port 0/0/0
!
dial-peer voice 101 pots
destination-pattern 9T
port 0/0/1
!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: