Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Disconnect Cause = 47 --- Q931 Debug --- Issue

Hello everybody.

Please help me with this.

Call from:

CM 6 ----> PBX Siemmens

When i call from "3001" to "5598" I receive "disconnect cause 47" with debug voip ccapi inout.

I try many thing how is possible with MTP, TXC and CFB (with or without RSVP)

On CCM Administration, Gateway have MTP on.

This is the GW configuration.

voice-card 0

dspfarm

dsp services dspfarm

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

supplementary-service h450.12

fax protocol t38 nse force ls-redundancy 0 hs-redundancy 0 fallback cisco

h323

  h225 timeout t302 2

  h225 timeout setup 3

modem passthrough nse codec g711ulaw

!

voice class codec 1

codec preference 1 g729r8

codec preference 2 g711ulaw

codec preference 3 g711alaw

!

voice class h323 1

h225 timeout tcp establish 3

!

controller E1 0/1/0

pri-group timeslots 1-31

!

interface GigabitEthernet0/0.100

description ## TELEFONIA ##

encapsulation dot1Q 100

ip address 10.73.4.1 255.255.252.0

zone-member security LAN

h323-gateway voip interface

h323-gateway voip bind srcaddr 10.73.4.1

!

!

interface Serial0/1/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn send-alerting

isdn sending-complete

no cdp enable

!

ccm-manager sccp local GigabitEthernet0/0.100

!

sccp local GigabitEthernet0/0.100

sccp ccm 10.73.4.3 identifier 1 version 5.0.1

sccp

!

sccp ccm group 1

bind interface GigabitEthernet0/0.100

associate ccm 1 priority 1

associate profile 1 register TXC_CAREMBAR

associate profile 2 register RSVP_CAREMBAR

associate profile 3 register CFB_CAREMBAR

switchover method immediate

!

dspfarm profile 1 transcode

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

rsvp

maximum sessions 4

associate application SCCP

!

dspfarm profile 3 conference

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

maximum sessions 2

associate application SCCP

!

dspfarm profile 2 mtp

codec pass-through

codec g711ulaw

rsvp

maximum sessions software 100

associate application SCCP

!

dial-peer voice 5598 pots

destination-pattern 5598

port 0/1/0:15

!

dial-peer voice 5500 pots

incoming called-number .

direct-inward-dial

port 0/1/0:15

!

dial-peer voice 1000 voip

description ## A CALL MANAGER ##

destination-pattern ....

voice-class codec 1

voice-class h323 1

session target ipv4:10.73.4.3

dtmf-relay h245-alphanumeric

fax rate disable

no vad

!

DEBUG ISDN Q931 !!! Try to understand why called number isnt appear.

Apr 26 14:52:24 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3001

Apr 26 14:52:24 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num

Apr 26 14:52:24 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00ED

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:28 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00ED

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:32 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00ED

        Cause i = 0x80E6 - Recovery on timer expiry

Apr 26 14:52:32 UTC: ISDN Se0/1/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK.  The SETUP failed.

Apr 26 14:52:32 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3001

Apr 26 14:52:32 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num

Apr 26 14:52:32 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00EE

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:36 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00EE

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:40 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x00EE

        Cause i = 0x80E6 - Recovery on timer expiry

Apr 26 14:52:40 UTC: ISDN Se0/1/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK.  The SETUP failed.

Apr 26 14:52:40 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num 3001

Apr 26 14:52:40 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Called num

Apr 26 14:52:40 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00EF

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:44 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00EF

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839F

                Exclusive, Channel 31

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80

                Plan:Unknown, Type:Unknown

Apr 26 14:52:45 UTC: ISDN Se0/1/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x00EF

        Cause i = 0x80AF - Resource unavailable, unspecified

Apr 26 14:53:15 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x00EF

        Cause i = 0x80AF - Resource unavailable, unspecified

Apr 26 14:53:19 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x00EF

        Cause i = 0x80AF - Resource unavailable, unspecified

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Disconnect Cause = 47 --- Q931 Debug --- Issue

PBX never replies messages from router.

Try setting router isdn network-side.

7 REPLIES
Hall of Fame Super Gold

Disconnect Cause = 47 --- Q931 Debug --- Issue

That is normal. On pots dial-peers you need to configure 'forward-digits all' to prevent the digitsin destianation-patern to be absorbed.

New Member

Disconnect Cause = 47 --- Q931 Debug --- Issue

Hi Pablo...

Thanks for your answer.

Youre right... now the number appear but the cause code is still the same.

SEE BOLD

Apr 26 15:24:05 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:24:05 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598

Apr 26 15:24:05 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F3

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:09 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F3

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:13 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref =                                                                                         0x00F3

        Cause i = 0x80E6 - Recovery on timer expiry

Apr 26 15:24:13 UTC: ISDN Se0/1/0:15 **ERROR**: CCPCC_CallOrigination: SETUP tim                                                                                        ed-out (2nd T303) to NETWORK.  The SETUP failed.

Apr 26 15:24:13 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:24:13 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598

Apr 26 15:24:13 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F4

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:16 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x00F                                                                                        2

        Cause i = 0x80AF - Resource unavailable, unspecified

Apr 26 15:24:17 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F4

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:20 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE pd = 8  callref = 0x00F                                                                                        2

        Cause i = 0x80AF - Resource unavailable, unspecified

Apr 26 15:24:21 UTC: ISDN Se0/1/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref =                                                                                         0x00F4

        Cause i = 0x80E6 - Recovery on timer expiry

Apr 26 15:24:21 UTC: ISDN Se0/1/0:15 **ERROR**: CCPCC_CallOrigination: SETUP tim                                                                                        ed-out (2nd T303) to NETWORK.  The SETUP failed.

Apr 26 15:24:21 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:24:21 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598

Apr 26 15:24:21 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F5

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:25 UTC: ISDN Se0/1/0:15 Q931: TX -> SETUP pd = 8  callref = 0x00F5

        Sending Complete

        Bearer Capability i = 0x8090A3

                Standard = CCITT

                Transfer Capability = Speech

                Transfer Mode = Circuit

                Transfer Rate = 64 kbit/s

        Channel ID i = 0xA9839E

                Exclusive, Channel 30

        Calling Party Number i = 0x0081, '3001'

                Plan:Unknown, Type:Unknown

        Called Party Number i = 0x80, '5598'

                Plan:Unknown, Type:Unknown

Apr 26 15:24:26 UTC: ISDN Se0/1/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0x                                                                                        00F5

        Cause i = 0x80AF - Resource unavailable, unspecified

arda#

Hall of Fame Super Gold

Disconnect Cause = 47 --- Q931 Debug --- Issue

PBX never replies messages from router.

Try setting router isdn network-side.

Cisco Employee

Disconnect Cause = 47 --- Q931 Debug --- Issue

Like Paulo, mentioned there is no call proceeding message from PBX at all, can you check with them what they didn't like in your setup ? Is it the plan/type ? If they can pinpoint, why they didnt respond then it would be much easier to isolate the issue ?

If you have  working scenario with the pbx, then you stare n compare the debugs and configuration.

Murali

New Member

Disconnect Cause = 47 --- Q931 Debug --- Issue

Thanks for your answer Marmugam... im talking now with Siemmens's guy.

I keep you in contact.

Thanks again.

New Member

Disconnect Cause = 47 --- Q931 Debug --- Issue

Thanks Paolo,

Now im thinking in issue on Siemmens side...

I put isdn protocol emulate network on serial 0/1/0:15... now i receive this.

Apr 26 15:41:41 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()

Apr 26 15:41:50 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()

Apr 26 15:41:59 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()

Apr 26 15:42:08 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()

Apr 26 15:42:13 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:42:13 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598BAD FRAME()

Apr 26 15:42:17 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2

Apr 26 15:42:17 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:42:17 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()                                                                                        BAD FRAME()

Apr 26 15:42:26 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from                                                                                         L2

Apr 26 15:42:26 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Calling num 3001

Apr 26 15:42:27 UTC: ISDN Se0/1/0:15 Q931: Applying typeplan for sw-type 0x12 is                                                                                         0x0 0x0, Called num 5598BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()BAD FRAME()

Apr 26 15:42:35 UTC: ISDN Se0/1/0:15 Q931: Ux_DLRelInd: DL_REL_IND received from 

Hall of Fame Super Gold

Disconnect Cause = 47 --- Q931 Debug --- Issue

Then PBX is network side, but doen't want to talk to router. Check with their technicians.

6903
Views
0
Helpful
7
Replies