The version 6.1(1A) will be running on a brand new server.
I ran the CallManager Upgrade Assistant file CCMUpgdAsstInstall.4-3-13.exe. And everything was OK exept the memory.
My old server is MCS-7835i-3.0-IPC1 with only 1 Gig of memory and as per the Upgrade assistant I need 2 Gig.
Could I run the DMA anyway ? It took me 3 hours to install the DMA software, and normally as per the documentation it take 20-40 minutes.... Could I expect my DMA will only take more time and it's suppose ?
Somebody have already try that ?
10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk =============================================== 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk ============ Resource Check Module ============ 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk =============================================== 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk INFO: User input of minimum memory required (string): 2000 MB 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk INFO: User input of minimum memory required (int): 2000 MB 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk INFO: The minimum memory requirement is 2000 MB 10/15/2010 22:10:38.549 Utilities.cpp instGetPhyscialMem Total Physical memory: 1073102848 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk INFO: The installed physical memory is 1073102848 Bytes 10/15/2010 22:10:38.549 ResourceCheck.cpp ResourceChk INFO: The installed physical memory is 1023 MB 10/15/2010 22:10:38.565 ResourceCheck.cpp ResourceChk iuRegQueryValueEx: Function started 10/15/2010 22:10:38.565 ResourceCheck.cpp ResourceChk iuRegQueryValueEx: Function ended 10/15/2010 22:10:38.565 ResourceCheck.cpp ResourceChk Info: Server is a CCM Publisher 10/15/2010 22:10:38.565 ResourceCheck.cpp ResourceChk ERR: The system does not meet the minimum memory requirement (expecting at least "2000" MB, but found "1023" MB) 10/15/2010 22:10:38.565 ResourceCheck.cpp ResourceChk INFO: Resouce Check Module return code: -10
Just to be sure, my new server mets the requirements for running the CUCM 6.1(1a) but the old publisher server whois running CCM 4.0(2a) where I will run the DMA software have only 1 gig of memory. After run the DMA on that server I will install directly on the new server CUCM 6.1(1a) with the .tar file.
Did you already, did that kind of upgrade where the Call Manager Upgrade Assistant give you that memory error ?
I fear to do DMA and the server crash because we don't have enought memory.
The short answer is that you don't.... That isn't entirely true while at
the same time it kind of is, but for the most part you don't configure
the softkeys. You enable or disable them via TCL. Here is the long
answer. Be sure to read the whole thing or e...
Topology: IP Phone > Switches > Microsoft NPS setup to forward 802.1x
proxy to > ISE 2.1 patch 3 Authentication: EAP-TLS using Cisco MIC SANs
Phone Models 802.1X support? 802.1x flavor Addtl Comment EAP-MD5 EAP-TLS
Cisco 3905 Y Y N Cisco 6911 Y Y N Cisco ...
This document describe how DST changes and how time changes are
implemented in DST. Daylight Saving Time (DST) is the practice of
setting the clocks forward 1 hour from standard time during the summer
months, and back again in the fall, in order to make b...