Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

DSPFarm in NM-2V is "DOWN"

Hi,

I have a 2621XM installed with NM-2V and VIC-2FXO, however, the dspfarm is always shown as "DOWN" and it doesn't allow me to use the "voice-card" command, any idea? Thanks.

Andrew

HE-VGW1#sh inventory
NAME: "2621XM chassis", DESCR: "2621XM chassis"
PID: C2621XM-2FE       , VID: 3.1, SN: XXXXXXXXXX

NAME: "C2600 4 port Voice PM", DESCR: "C2600 4 port Voice PM"
PID: NM-2V=            , VID: 1.1, SN: XXXXXXXX

NAME: "Two port FXO voice interface daughtercard", DESCR: "Two port FXO voice in
terface daughtercard"
PID: VIC-2FXO=         , VID: 1.1, SN: XXXXXXXX


HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#sh dspfar
HE-VGW1#sh dspfarm
DSPFARM Configuration Information:
Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN
Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)
Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600
Connection check interval 600 Codec G729 VAD: ENABLED
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#
HE-VGW1#config t
Enter configuration commands, one per line.  End with CNTL/Z.
HE-VGW1(config)#voice-card 0
                           ^
% Invalid input detected at '^' marker.

HE-VGW1(config)#

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Gold

Re: DSPFarm in NM-2V is "DOWN"

No, they can't.

Use current hardware for that.

4 REPLIES
Bronze

Re: DSPFarm in NM-2V is "DOWN"

I think your using the wrong commands.To access a FXO port you need to use the voice-port command.If you do a sh run you should see them, something like

voice-port 0/0/0 or similiar.

cheers

Mark

Cisco Employee

Re: DSPFarm in NM-2V is "DOWN"

I don't see any DSPs listed in the inventory, you need DSPs for voice termination or to configure DSPfarms

HTH

java

If this helps, please rate

www.cisco.com/go/pdihelpdesk

HTH

java

if this helps, please rate

www.cisco.com/go/pdi
New Member

Re: DSPFarm in NM-2V is "DOWN"

Hi,

DSPs are present on the NM-2V, I wonder if they can be used as media resources (hardware conference bridge) for CUCM?

Thanks,


Andrew

HE-VGW1#sh voice dsp

DSP  DSP                DSPWARE CURR  BOOT                         PAK     TX/RX
TYPE NUM CH CODEC       VERSION STATE STATE   RST AI VOICEPORT TS ABORT  PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
C542 001 01 None         4.4.29 IDLE  idle      0  0 1/0/0     NA     0    3822/4161
C542 002 01 None         4.4.29 IDLE  idle      0  0 1/0/1     NA     0      594/591

Hall of Fame Super Gold

Re: DSPFarm in NM-2V is "DOWN"

No, they can't.

Use current hardware for that.

1031
Views
0
Helpful
4
Replies