Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

DSPs - State: APP_DNLDING - conference max session 0

hi,

i have a 2901 with 15.2(2)M and one PVDM3-16 installed. I try to get working an ad-hoc conference but when i enter the command

dsp profile 1 conference

maximum session <0-0>

0 sessions?

-----------------------------------------------------------------------------

Router2901#sh voice dsp group all

DSP groups on slot 0:

dsp 1:

State: APP_DNLDING, firmware: 0.0.0

Max signal/voice channel: 16/16

Max credits: 240, Voice credits: 240, Video credits: 0

num_of_sig_chnls_allocated: 0

Transcoding channels allocated: 0

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 0

Voice channels allocated: 0

Credits used (rounded-up): 0

Slot: 0

Device idx: 0

PVDM Slot: 0

Dsp Type: SP2600

DSP groups on slot 1:

This command is not applicable to slot 1

0 DSP resource allocation failure

-----------------------------------------------------------------------------

Router2901#sh dspfarm all

Dspfarm Profile Configuration

Profile ID = 1, Service = CONFERENCING, Resource ID = 1

Profile Description :

Profile Service Mode : Non Secure

Profile Admin State : DOWN

Profile Operation State : DOWN

Application : SCCP   Status : NOT ASSOCIATED

Resource Provider : FLEX_DSPRM   Status : NONE

Number of Resource Configured : 0

Number of Resource Available : 0

Maximum conference participants : 8

Codec Configuration: num_of_codecs:6

Codec : g711ulaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Codec : g711alaw, Maximum Packetization Period : 30 , Transcoder: Not Required

Codec : g729ar8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729abr8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729r8, Maximum Packetization Period : 60 , Transcoder: Not Required

Codec : g729br8, Maximum Packetization Period : 60 , Transcoder: Not Required

Total number of DSPFARM DSP channel(s) 0

--------------------------------------------------------

what could it be?

thank

6 REPLIES
Blue

DSPs - State: APP_DNLDING - conference max session 0

HI

Can you please share show diag of the router.

Regards

Ronak Patel

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

DSPs - State: APP_DNLDING - conference max session 0

Hi Ronak,

here is the show diag

----------------------

Slot 0:

C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 2 ports

Port adapter is analyzed

....

PVDM Slot 0:

16-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card

Hardware Revision        : 1.0

Part Number              : XXXX

Board Revision           : B0

Deviation Number         : 0

Fab Version              : 03

PCB Serial Number        : XXXX

RMA Test History         : 00

RMA Number               : 0-0-0-0

RMA History              : 00

Processor type           : 00

Product (FRU) Number     : PVDM3-16

Version Identifier       : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 05 D8 41 01 00 82 49 2D 38 03 42 42 30

0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 34 32 38

0x20: 30 38 50 58 03 00 81 00 00 00 00 04 00 09 00 CB

0x30: 8F 50 56 44 4D 33 2D 31 36 20 20 20 20 20 20 20

0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Embedded Service Engine 0/0 :

Total platform memory : 524288K bytes

Total 2nd core memory : 0K bytes

Start of physical address for 2nd core : 0x80000000

Virtual address start of 2nd core memory : 0x0 - 0x0

2nd core configured disabled

L2 cache ways for 2nd core : 0

------------------------------

thx Konrad

Blue

DSPs - State: APP_DNLDING - conference max session 0

HI

This issue happens when you have not accepted license aggrement EULA in the router. Have you accepted the EULA and reload the router after it.

Regards

Ronak patel

Please rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

DSPs - State: APP_DNLDING - conference max session 0

Hi,

i can't remind, but i tried now with following command

license accept end user agreement

yes

reload

but it's the same behaviour

Blue

DSPs - State: APP_DNLDING - conference max session 0

Hi,

There was a bug but it got resolved in 15.1.2 release.

Can you share the sh run of the router.

regards

Ronak patel

Rate helpful posts.

Regards Ronak Patel Rate all helpful post by clicking stars below the answer.

DSPs - State: APP_DNLDING - conference max session 0

Hi Ronak,

thanks for your help - DSP hardware failure was the problem.

Konrad.

1576
Views
18
Helpful
6
Replies