Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

dtmf issue on uc540

 
1 ACCEPTED SOLUTION

Accepted Solutions
VIP Super Bronze

dtmf issue on uc540

Your CUE is configured for rtp-nte

ccn subsystem sip

gateway address "10.1.10.2"

dtmf-relay rtp-nte

end subsystem

ccn subsystem sip

Please change this to

conf t

ccn subsystem sip

dtmf-relay sip-notify

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
19 REPLIES

dtmf issue on uc540

Hi

Check if you CUE is working properly, once that is not working fron inside

Cheers
Bruno Rangel

Please remember to rate helpful  responses using the stars bellow and identify helpful or correct answers .

Cheers Bruno Rangel Please remember to rate helpful responses using the stars bellow and identify helpful or correct answers .
New Member

dtmf issue on uc540

What do you mean by check from inside???

i have already checked its working fine....its pinging, I can open cli of cue,Gui also works fine.

dtmf issue on uc540

I mean if it´s working from a Internal extension

mohd abdul malik wrote:

Not only i am facing this issue when i am calling from outside but also  internally therfore am guessing this issue is related to configuration

Cheers
Bruno Rangel

Please remember to rate helpful  responses using the stars bellow and identify helpful or correct answers .

Cheers Bruno Rangel Please remember to rate helpful responses using the stars bellow and identify helpful or correct answers .
New Member

dtmf issue on uc540

nope its not working for internal extensions also.

Is my configuration alright??

dtmf issue on uc540

Hi Abdul,

show run (From the CUE)

Regards,

Kevin

New Member

Re: dtmf issue on uc540

Hi kevin,

Thanks for taking interest in my issue I really appreciate your concern for other.

VIP Super Bronze

dtmf issue on uc540

Abdul,

You didnt post the dial-peers for the CUE. Do you have sip notify configured on the dial-peer pointing to CUE on the UC520?

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: dtmf issue on uc540

Hi Aokanlawon,

I have posted the dialpeer in my initial question, Please have a look.

New Member

Re: dtmf issue on uc540

Now i have also done the dtmf-relay sip notify configuration on the dial-peer voice 750 voip.

dial-peer voice 750 voip

destination-pattern 750

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

Still its not working

Re: dtmf issue on uc540

Hi

You received busy tone ? Post the output of debbug voice ccapi inout.

Also try no incoming called number . in your DP

Cheers Bruno Rangel Please remember to rate helpful responses using the stars bellow and identify helpful or correct answers .
New Member

Re: dtmf issue on uc540

Please check the attached requested debugs.

VIP Super Bronze

Re: dtmf issue on uc540

Can you post your full sh run..What is configured on dial-peer 102?

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: dtmf issue on uc540

Well 102 is an incoming dial-peer.

but its taking the dial peer 750 to route the cals to cue.

VIP Super Bronze

dtmf issue on uc540

Your CUE is configured for rtp-nte

ccn subsystem sip

gateway address "10.1.10.2"

dtmf-relay rtp-nte

end subsystem

ccn subsystem sip

Please change this to

conf t

ccn subsystem sip

dtmf-relay sip-notify

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: dtmf issue on uc540

still not working just AA plays on and on until the call gets disconnected.

VIP Super Bronze

dtmf issue on uc540

pls send debug ccsip messages

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: dtmf issue on uc540

Thanks a  LOOOOOOOOOOOOOOOOOOT

I checked again after 2-3 calls it started working.

I am really impressed!!!!

I have sent you a personal message could you pls check and help me further.

VIP Super Bronze

Re: dtmf issue on uc540

I have replied to your PM. Can you do me a favour and send me a debug ccsip message of a working call..I want to confirm something...

Please rate all useful posts

"The essence of christianity is not the enthronement but the obliteration of self --William Barclay"

Please rate all useful posts "The essence of christianity is not the enthronement but the obliteration of self --William Barclay"
New Member

Re: dtmf issue on uc540

Please find the attached file for requested debugs of a successful call.

        do let me know if you need anything further.

339
Views
33
Helpful
19
Replies
CreatePlease to create content